- 您現在的位置：買賣IC網 > PDF目錄374731 > SC470IMLTRT (Semtech Corporation) Synchronous Buck Controller for Dynamic Load-Voltage Applications PDF資料下載
參數資料
| 型號： | SC470IMLTRT |
| 廠商： | Semtech Corporation |
| 英文描述： | Synchronous Buck Controller for Dynamic Load-Voltage Applications |
| 中文描述： | 同步降壓控制器的動態負載電壓應用 |
| 文件頁數： | 11/31頁 |
| 文件大?。?/td> | 574K |
| 代理商： | SC470IMLTRT |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁當前第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁
11
2005 Semtech Corp.
www.semtech.com
SC470
POWER MANAGEMENT
Application Information (Cont.)
(maximum) minimum off-time one-shot. For best dropout
performance, use the slowest on-time setting of 200kHz.
When working with low input voltages, the duty-factor
limit must be calculated using worst-case values for on
and off times. The IC duty-factor limitation is given by:
t
DUTY
+
)
MAX
(
OFF
t
)
MIN
(
ON
t
)
MIN
(
ON
=
Be sure to include inductor resistance and MOSFET on-
state voltage drops when performing worst-case dropout
duty-factor calculations.
470 System DC Accuracy
Two IC parameters affect system DC accuracy, the error
comparator threshold voltage variation and the switching
frequency variation with line and load. The error
comparator threshold does not drift significantly with
supply and temperature. Thus, the error comparator
contributes 0.85% or less to DC system inaccuracy.
Board components and layout also influence DC
accuracy. The use of 1% feedback resistors contribute
1%. If tighter DC accuracy is required use 0.1% feedback
resistors.
The on-pulse in the SC470 is calculated to give a pseudo-
fixed frequency. Nevertheless, some frequency variation
with line and load can be expected. This variation changes
the output ripple voltage. Because constant on-
regulators regulate to the valley of the output ripple,
of the output ripple appears as a DC regulation error.
For example, if the feedback resistors are chosen to
divide down the output by a factor of five, the valley of
the output ripple will be VOUT. For example: if VOUT is
2.5V and the ripple is 50mV with VBAT = 6V, then the
measured DC output will be 2.525V. If the ripple increases
to 80mV with VBAT = 25V, then the measured DC output
will be 2.540V.
The output inductor value may change with current. This
will change the output ripple and thus the DC output
voltage. It will not change the frequency.
Switching frequency variation with load can be minimized
by choosing MOSFETs with lower R
. High R
MOSFETs will cause the switching frequency to increase
as the load current increases. This will reduce the ripple
and thus the DC output voltage.
Design Procedure
Prior to designing an output and making component
selections, it is necessary to determine the input voltage
range and the output voltage specifications. For purposes
of demonstrating the procedure the output for the
schematic in Figure 8 on Page 17 will be designed.
The maximum input voltage (V
) is determined by
the highest AC adaptor voltage. The minimum input
voltage (V
) is determined by the lowest battery
voltage after accounting for voltage drops due to
connectors, fuses and battery selector switches. For the
purposes of this design we will use a V
BAT
range of 8V to
20V.
Four parameters are needed for the output:
1) Nominal output voltage, V
(we will use 1.2V).
2) Static (or DC) tolerance, TOL
(we will use +/-4%).
3) Transient tolerance, TOL
and size of transient (we
will use +/-8% for purposes of this demonstration).
4) Maximum output current, I
OUT
(we will design for 6A).
Switching frequency determines the trade-off between
size and efficiency. Increased frequency increases the
switching losses in the MOSFETs, since losses are a
function of VIN
2
, knowing the maximum input voltage and
budget for MOSFET switches usually dictates where the
design ends up. A default R
value of 1M
is suggested
as a starting point, but this is not set in stone. The first
thing to do is to calculate the on-time, t
ON
, at V
BAT(MIN)
and
V
BAT(MAX)
, since this depends only upon V
BAT
, V
OUT
tON
.
For V
OUT
< 3.3V:
(
)
s
10
50
V
V
10
37
R
10
3
t
9
)
MIN
(
BAT
OUT
3
tON
12
)
MIN
(
VBAT
_
ON
+
+
=
and,
(
)
s
10
50
V
V
10
37
R
10
3
t
9
)
MAX
(
BAT
OUT
3
tON
12
)
MAX
(
VBAT
_
ON
+
+
=
From these values of t
we can calculate the nominal
switching frequency as follows:
相關PDF資料 |
PDF描述 |
|---|---|
| SC470ITSTRT | Synchronous Buck Controller for Dynamic Load-Voltage Applications |
| SC471EVB | Synchronous Buck Controller with Multi-Level VOUT Transition Support |
| SC471MLTRT | Synchronous Buck Controller with Multi-Level VOUT Transition Support |
| SC471 | Synchronous Buck Controller with Multi-Level VOUT Transition Support |
| SC471A | Synchronous Buck Controller with Multi-Level VOUT Transition Support |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SC470ITSTRT | 功能描述:IC REG CTRLR BUCK PWM 14-TSSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 特色產品:LM3753/54 Scalable 2-Phase Synchronous Buck Controllers 標準包裝:1 系列:PowerWise® PWM 型:電壓模式 輸出數:1 頻率 - 最大:1MHz 占空比:81% 電源電壓:4.5 V ~ 18 V 降壓:是 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-5°C ~ 125°C 封裝/外殼:32-WFQFN 裸露焊盤 包裝:Digi-Reel® 產品目錄頁面:1303 (CN2011-ZH PDF) 其它名稱:LM3754SQDKR |
| SC471 | 制造商:SEMTECH 制造商全稱:Semtech Corporation 功能描述:Synchronous Buck Controller with Multi-Level VOUT Transition Support |
| SC471_08 | 制造商:SEMTECH 制造商全稱:Semtech Corporation 功能描述:Synchronous Buck Controller with Multi-Level VOUT Transition Support |
| SC471A | 制造商:SEMTECH 制造商全稱:Semtech Corporation 功能描述:Synchronous Buck Controller with Multi-Level VOUT Transition Support |
| SC471AEVB | 制造商:SEMTECH 制造商全稱:Semtech Corporation 功能描述:Synchronous Buck Controller with Multi-Level VOUT Transition Support |
發布緊急采購，3分鐘左右您將得到回復。