參數資料
型號: SC16C850IBS,157
廠商: NXP Semiconductors
文件頁數: 20/55頁
文件大?。?/td> 0K
描述: IC UART SGL W/FIFO 32HVQFN
標準包裝: 2,450
特點: 可編程
通道數: 1,UART
FIFO's: 128 字節
規程: RS485
電源電壓: 2.5 V ~ 3.3 V
帶自動流量控制功能:
帶IrDA 編碼器/解碼器:
帶故障啟動位檢測功能:
帶調制解調器控制功能:
帶CMOS:
安裝類型: 表面貼裝
封裝/外殼: 32-VFQFN 裸露焊盤
供應商設備封裝: 32-HVQFN(5x5)
包裝: 托盤
SC16C850
All information provided in this document is subject to legal disclaimers.
NXP B.V. 2010. All rights reserved.
Product data sheet
Rev. 2 — 11 November 2010
27 of 55
NXP Semiconductors
SC16C850
2.5 to 3.3 V UART with 128-byte FIFOs and IrDA encoder/decoder
7.5 Line Control Register (LCR)
The Line Control Register is used to specify the asynchronous data communication
format. The word length, the number of stop bits, and the parity are selected by writing the
appropriate bits in this register.
0
ISR[0]
INT status.
logic 0 = an interrupt is pending and the ISR contents may be used as a
pointer to the appropriate interrupt service routine
logic 1 = no interrupt pending (normal default condition)
Table 14.
Interrupt Status Register bits description …continued
Bit
Symbol
Description
Table 15.
Line Control Register bits description
Bit
Symbol
Description
7
LCR[7]
Divisor latch enable. The internal baud rate counter latch and Enhanced
Feature mode enable.
logic 0 = divisor latch disabled (normal default condition)
logic 1 = divisor latch enabled
6
LCR[6]
Set break. When enabled, the Break control bit causes a break condition to
be transmitted (the TX output is forced to a logic 0 state). This condition
exists until disabled by setting LCR[6] to a logic 0.
logic 0 = no TX break condition (normal default condition)
logic 1 = forces the transmitter output (TX) to a logic 0 for alerting the
remote receiver to a line break condition
5:3
LCR[5:3]
Programs the parity conditions (see Table 16).
2
LCR[2]
Stop bits. The length of stop bit is specified by this bit in conjunction with the
programmed word length (see Table 17).
logic 0 or cleared = default condition
1:0
LCR[1:0]
Word length bits 1, 0. These two bits specify the word length to be
transmitted or received (see Table 18).
logic 0 or cleared = default condition
Table 16.
LCR[5:3] parity selection
LCR[5]
LCR[4]
LCR[3]
Parity selection
XX
0
no parity
0
01odd parity
0
11even parity
1
0
1
forced parity ‘1’
1
forced parity ‘0’
Table 17.
LCR[2] stop bit length
LCR[2]
Word length (bits)
Stop bit length (bit times)
0
5, 6, 7, 8
1
15
11
2
16, 7, 8
2
相關PDF資料
PDF描述
VE-B7J-IX-F2 CONVERTER MOD DC/DC 36V 75W
VE-B24-IY CONVERTER MOD DC/DC 48V 50W
SC16IS760IPW,128 IC UART 64BYTE 24TSSOP
VE-B7J-IX-F1 CONVERTER MOD DC/DC 36V 75W
VE-B21-IY CONVERTER MOD DC/DC 12V 50W
相關代理商/技術參數
參數描述
SC16C850IET 功能描述:UART 接口集成電路 16C 2.5-5V 5MBPS UART 128BFIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
SC16C850IET,115 功能描述:UART 接口集成電路 16C 2.5-5V 5MBPS RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
SC16C850IET,151 功能描述:UART 接口集成電路 16C 2.5-5V 5MBPS RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
SC16C850IET,157 功能描述:UART 接口集成電路 16C 2.5-5V 5MBPS RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
SC16C850IET-G 功能描述:UART 接口集成電路 16C 2.5-5V 5MBPS UART 128BFIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel