參數資料
型號: SC16C650BIN40
廠商: NXP SEMICONDUCTORS
元件分類: 微控制器/微處理器
英文描述: 5 V, 3.3 V and 2.5 V UART with 32-byte FIFOs and infrared (IrDA) encoder/decoder
中文描述: 1 CHANNEL(S), 3M bps, SERIAL COMM CONTROLLER, PDIP40
封裝: 0.600 INCH, PLASTIC, MO-015, SOT-129-1, DIP-40
文件頁數: 14/51頁
文件大?。?/td> 881K
代理商: SC16C650BIN40
Philips Semiconductors
SC16C650B
UART with 32-byte FIFOs and IrDA encoder/decoder
Product data
Rev. 03 — 10 December 2004
14 of 51
9397 750 14451
Koninklijke Philips Electronics N.V. 2004. All rights reserved.
6.7 Programmable baud rate generator
The SC16C650B supports high speed modem technologies that have increased
input data rates by employing data compression schemes. For example, a 33.6 kbit/s
modem that employs data compression may require a 115.2 kbit/s input data rate.
A 128.0 kbit/s ISDN modem that supports data compression may need an input
data rate of 460.8 kbit/s.
A single baud rate generator is provided for the transmitter and receiver, allowing
independent TX/RX channel control. The programmable Baud Rate Generator is
capable of accepting an input clock up to 48 MHz, as required for supporting a
3 Mbit/s data rate. The SC16C650B can be configured for internal or external clock
operation. For internal clock oscillator operation, an industry standard microprocessor
crystal (parallel resonant/22-33 pF load) is connected externally between the XTAL1
and XTAL2 pins (see
Figure 6
). Alternatively, an external clock can be connected to
the XTAL1 pin to clock the internal baud rate generator for standard or custom rates
(see
Table 5
).
The generator divides the input 16
×
clock by any divisor from 1 to 2
16
1. The
SC16C650B divides the basic crystal or external clock by 16. The frequency of the
BAUDOUT output pin is exactly 16
×
(16 times) of the selected baud rate
(BAUDOUT = 16 Baud Rate). Customized baud rates can be achieved by selecting
the proper divisor values for the MSB and LSB sections of baud rate generator.
Setting MCR[7] to a logic 1 provides an additional divide-by-4, whereas setting
MCR[7] to a logic 0 only divides by 1 (see
Table 5
and
Figure 7
).
Programming the Baud Rate Generator registers DLM (MSB) and DLL (LSB)
provides a user capability for selecting the desired final baud rate. The example in
Table 5
shows selectable baud rates when using a 1.8432 MHz crystal and setting
MCR[7] to a logic 0.
For custom baud rates, the divisor value can be calculated using the following
equation:
(1)
Fig 6.
Crystal oscillator connection.
002aaa586
X1
1.8432 MHz
C1
22 pF
C2
47 pF
X
X
X1
1.8432 MHz
C1
22 pF
C2
33 pF
X
X
1.5 k
Divisor (in decimal)
serial data rate
16
----------------------------------------------------------
=
相關PDF資料
PDF描述
SC16C652B 5V, 3.3 V and 2.5V dual UART, 5 Mbit/s (max.),with 32-byte FIFOs and infrared(IrDA) encoder/decoder
SC16C652 Dual UART with 32 bytes of transmit and receive FIFOs
SC16C652IB48 Dual UART with 32 bytes of transmit and receive FIFOs
SC16C654IB64 Quad UART with 64-byte FIFO and infrared (IrDA) encoder/decoder
SC16C654 Quad UART with 64-byte FIFO and infrared (IrDA) encoder/decoder
相關代理商/技術參數
參數描述
SC16C650BIN40,112 功能描述:UART 接口集成電路 16CB 2.5V-5V 1CH RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
SC16C652 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Dual UART with 32 bytes of transmit and receive FIFOs
SC16C652B 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:5V, 3.3 V and 2.5V dual UART, 5 Mbit/s (max.),with 32-byte FIFOs and infrared(IrDA) encoder/decoder
SC16C652BIB48 功能描述:UART 接口集成電路 16CB 2.5V-5V 2CH UART 32B FIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel
SC16C652BIB48,128 功能描述:UART 接口集成電路 16CB 2.5V-5V 2CH RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel