- 您現在的位置：買賣IC網 > PDF目錄1967 > SC16C2550BIB48,157 (NXP Semiconductors)IC UART DUAL W/FIFO 48-LQFP PDF資料下載
參數資料
| 型號： | SC16C2550BIB48,157 |
| 廠商： | NXP Semiconductors |
| 文件頁數： | 19/31頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC UART DUAL W/FIFO 48-LQFP |
| 標準包裝： | 1,250 |
| 特點： | 故障啟動位檢測 |
| 通道數： | 2，DUART |
| FIFO's： | 16 字節(jié) |
| 電源電壓： | 2.5V，3.3V，5V |
| 帶自動流量控制功能： | 是 |
| 帶故障啟動位檢測功能： | 是 |
| 帶調制解調器控制功能： | 是 |
| 帶CMOS： | 是 |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 48-LQFP |
| 供應商設備封裝： | 48-LQFP（7x7） |
| 包裝： | 托盤 |
| 其它名稱： | 935274406157 SC16C2550BIB48 SC16C2550BIB48-ND |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁當前第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁
37
2570N–AVR–05/11
ATmega325/3250/645/6450
10.6
Standby Mode
When the SM2..0 bits are 110 and an external crystal/resonator clock option is selected, the
SLEEP instruction makes the MCU enter Standby mode. This mode is identical to Power-down
with the exception that the Oscillator is kept running. From Standby mode, the device wakes up
in six clock cycles.
10.7
Power Reduction Register
The Power Reduction Register (PRR), see “PRR – Power Reduction Register” on page 40, pro-
vides a method to stop the clock to individual peripherals to reduce power consumption. The
current state of the peripheral is frozen and the I/O registers inaccessible. Resources used by
the peripheral when stopping the clock will remain occupied so the peripheral should be disabled
before stopping the clock. Waking up a peripheral, which is done by clearing the bit in PRR, puts
the peripheral in the same state as before shutdown.
Peripheral shutdown can be used in Idle mode and Active mode to reduce the overall power
consumption. In all other sleep modes, the clock is already stopped.
10.8
Minimizing Power Consumption
There are several possibilities to consider when trying to minimize the power consumption in an
AVR controlled system. In general, sleep modes should be used as much as possible, and the
sleep mode should be selected so that as few as possible of the device’s functions are operat-
ing. All functions not needed should be disabled. In particular, the following modules may need
special consideration when trying to achieve the lowest possible power consumption.
10.8.1
Analog to Digital Converter
If enabled, the ADC will be enabled in all sleep modes. To save power, the ADC should be dis-
abled before entering any sleep mode. When the ADC is turned off and on again, the next
conversion will be an extended conversion. Refer to “Analog to Digital Converter” on page 201
for details on ADC operation.
10.8.2
Analog Comparator
When entering Idle mode, the Analog Comparator should be disabled if not used. When entering
ADC Noise Reduction mode, the Analog Comparator should be disabled. In other sleep modes,
the Analog Comparator is automatically disabled. However, if the Analog Comparator is set up
to use the Internal Voltage Reference as input, the Analog Comparator should be disabled in all
sleep modes. Otherwise, the Internal Voltage Reference will be enabled, independent of sleep
mode. Refer to “Analog Comparator” on page 197 for details on how to configure the Analog
Comparator.
10.8.3
Brown-out Detector
If the Brown-out Detector is not needed by the application, this module should be turned off. If
the Brown-out Detector is enabled by the BODLEVEL Fuses, it will be enabled in all sleep
modes, and hence, always consume power. In the deeper sleep modes, this will contribute sig-
nificantly to the total current consumption. Refer to “Brown-out Detection” on page 43 for details
on how to configure the Brown-out Detector.
10.8.4
Internal Voltage Reference
The Internal Voltage Reference will be enabled when needed by the Brown-out Detection, the
Analog Comparator or the ADC. If these modules are disabled as described in the sections
相關PDF資料 |
PDF描述 |
|---|---|
| SC16C2550IB48,151 | IC UART DUAL W/FIFO 48-LQFP |
| SC16C2552BIA44,529 | IC UART DUAL W/FIFO 44-PLCC |
| SC16C550BIB48,157 | IC UART SINGLE W/FIFO 48-LQFP |
| SC16C554DBIA68,529 | IC UART QUAD W/FIFO 68-PLCC |
| SC16C554IB80,528 | IC UART QUAD SOT315-1 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SC16C2550BIB48-S | 功能描述:UART 接口集成電路 2CH. UART 16B FIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| SC16C2550BIBS | 功能描述:UART 接口集成電路 16CB 2.5V-5V 2CH UART 16B FIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| SC16C2550BIBS,128 | 功能描述:UART 接口集成電路 16CB 2.5V-5V 2CH RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| SC16C2550BIBS,151 | 功能描述:UART 接口集成電路 2CH. UART 16B FIFO RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
| SC16C2550BIBS,157 | 功能描述:UART 接口集成電路 16CB 2.5V-5V 2CH RoHS:否 制造商:Texas Instruments 通道數量:2 數據速率:3 Mbps 電源電壓-最大:3.6 V 電源電壓-最小:2.7 V 電源電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:LQFP-48 封裝:Reel |
發(fā)布緊急采購，3分鐘左右您將得到回復。