參數資料
型號： SC1401ISS
廠商： Semtech Corporation
英文描述： HIGH PERFORMANCE SYNCHRONOUS BUCK CONTROLLER WITH LDO FOR PORTABLE POWER
中文描述： 高性能同步降壓控制器的便攜式功率穩壓器
文件頁數： 12/17頁
文件大?。?/td> 202K
代理商： SC1401ISS
SC1401
2000 SEMTECH CORP.
652 MITCHELL ROAD NEWBURY PARK CA 91320
HIGH PERFORMANCE SYNCHRONOUS BUCK
CONTROLLER WITH LDO FOR PORTABLE
POWER
November 21, 2000
12
TEL:805-498-2111 FAX:805-498-3804 WEB:http://www.semtech.com
Detailed Description
The SC1401 is a high performance, high efficiency,
PWM synchronous buck controller, designed to
power the latest generation microprocessors in
battery operated systems. Two high-current gate
drive outputs are supplied to control both MOSFETs
in the synchronous rectified buck converter. This
power supply can be programmed to operate at
either fixed (1.25V) or adjustable output voltages.
The power save feature enables high efficiency over
a wide range of load current. The control and fault
monitoring circuitry associated with the PWM
controller includes digital softstart, turn-on
sequencing, frequency compensation, power save,
overcurrent and over and under voltage fault
protection. An LDO NMOS linear regulator is also
generated by the SC1401. A block diagram of the
SC1401 is shown in Figure 1.
PWM Control Block
The SC1401 employs peak-current-mode control with
slope compensation to provide fast output response
to load and line transients. The PWM control block
consists of an analog PWM modulator followed by
PWM logic control. The analog modulator combines
the current output, slope compensation signal and
error voltage to generate a PWM pulse train. The
PWM logic uses the pulse train from the modulator
and other control signals to generate the output
states for the high and low side gate driver outputs.
A block diagram of the PWM control block is shown
in Figure 2.
An error amplifier generates the difference signal
between the reference voltage and the feedback
voltage to generate the control voltage for the peak
current mode comparator. A nominal gain of 8 is
used in the error amplifier to further increase the
system loop-gain and reduce the load regulation
error typically seen with low loop-gain current mode
controllers. The increased gain in the voltage loop is
compensated by pole-zero-pole response of the
voltage error amplifier. The current feedback signal
is summed with the slope compensation signal and
compared to the control voltage by the PWM
comparator.
When the power supply is operating in continuous
conduction mode with current > 25% of its peak
value, the high side MOSFET is turned on at the
beginning of each switching cycle. The high-side
MOSFET is turned off when the desired duty cycle is
reached. Active shoot-through protection delays the
turn-on of the low-side power device until the
PHASE node drops below 1.25V. The low-side
devices remains on until the beginning of the next
switching cycle. Again, active shoot-through
protection ensures that the gate to the low-side
power device is low before the high-side device is
turned on.
When PSAVE is enabled (low) and the output
current drops below 25% of its peak level, the PWM
logic will automatically enter PSAVE mode to
improve efficiency. When the controller enters
power save, it increases the regulation point by
0.8%, typically issuing one more high side pulse as
the converter enters PSAVE. The PWM control
then disables switching cycles until the FB falls
below the reference. At light loads the effective
switching frequency will drop dramatically and
efficiency will increase because of the reduced gate
charge current required to switch the power stage.
Boosting the regulation point when entering PSAVE
gives the output improved dynamic regulation
because the output voltage is not allowed to droop
below the nominal regulation point. Load current
steps, that cause the converter to come out of
PSAVE, will not cause as large a negative dip in the
output voltage.
The PSAVE threshold is a function of the load and
peak-to-peak inductor current. It can be calculated
by the following equations:
!
I
L
= peak-to-peak inductor current
I
O
= Load Current
V
IN
= Input Voltage
V
O
= Output Voltage
D = Duty Cycle
f = Frequency
L = Inductance
S
L
O
THPSAVE
R
2
I
I
V
=
(
)
f
D
L
V
-
V
I
O
IN
L
=
相關PDF資料
PDF描述
SC1401 High Performance Synchronous Buck Controller with LDO for Portable Power(用于便攜式電源帶低壓差輸出的高性能同步步降控制器（1.25-5.5V可調輸出）)
SC1402 Multi-Output, Low-Noise Power Supply Controller for Notebook Computers
SC1402ISS Multi-Output, Low-Noise Power Supply Controller for Notebook Computers
SC1403ITSTRT Mobile Multi-Output PWM Controller with Lossless Current Sense
SC1403 Mobile Multi-Output PWM Controller with Virtual Current SenseTM
相關代理商/技術參數
參數描述
SC1402 制造商:SEMTECH 制造商全稱:Semtech Corporation 功能描述:Multi-Output, Low-Noise Power Supply Controller for Notebook Computers
SC1402ISS 制造商:SEMTECH 制造商全稱:Semtech Corporation 功能描述:Multi-Output, Low-Noise Power Supply Controller for Notebook Computers
SC1403 制造商:SEMTECH 制造商全稱:Semtech Corporation 功能描述:Mobile Multi-Output PWM Controller with Virtual Current SenseTM
SC1403_04 制造商:SEMTECH 制造商全稱:Semtech Corporation 功能描述:Mobile Multi-Output PWM Controller with Lossless Current Sense
SC1403ITSTR 制造商:Semtech Corporation 功能描述:IC, MULTI-OUTPUT PWM CONTROLLER, 28-TSSOP, Primary Input Voltage:15V, No. of Out
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*