![](http://datasheet.mmic.net.cn/40000/SBM0203R_datasheet_1661376/SBM0203R_4.png)
Electrical Characteristics V
The following specifications apply for V
DD = 2.6V, AV = 1, and 32 load unless otherwise specified. Limits apply to TA = 25°C.
Symbol
Parameter
Conditions
LM4910
Units
(Limits)
Typ
Limit
I
DD
Quiescent Power Supply Current
V
IN = 0V, 32 Load
3.0
mA (max)
I
SD
Standby Current
V
SHUTDOWN = GND
0.1
A (max)
V
OS
Output Offset Voltage
5
mV (max)
P
O
Output Power
THD = 1% (max); f = 1kHz
13
mW
THD+N
Total Harmonic Distortion + Noise P
O = 10mWrms; f = 1kHz
0.3
%
PSRR
Power Supply Rejection Ratio
V
RIPPLE = 200mVp-p sinewave
Input terminated with 10
to ground
55 (f =
217Hz)
55 (f =
1kHz)
dB
Note 1:
All voltages are measured with respect to the GND pin unless otherwise specified.
Note 2:
Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is
functional but do not guarantee specific performance limits. Electrical Characteristics state DC and AC electrical specifications under particular test conditions
which guarantee specific performance limits. This assumes that the device is within the Operating Ratings. Specifications are not guaranteed for parameters
where no limit is given, however, the typical value is a good indication of device performance.
Note 3:
The maximum power dissipation must be derated at elevated temperatures and is dictated by T
JMAX, θJA, and the ambient temperature, TA. The maximum
allowable power dissipation is P
DMAX = (TJMAX - TA)/ θJA or the number given in Absolute Maximum Ratings, whichever is lower. For the LM4910, see power
derating currents for more information.
Note 4:
Human body model, 100pF discharged through a 1.5k
resistor.
Note 5:
Machine Model, 220pF-240pF discharged through all pins.
Note 6:
Typicals are measured at 25°C and represent the parametric norm.
Note 7:
Limits are guaranteed to National's AOQL (Average Outgoing Quality Level).
Note 8:
Datasheet min/max specification limits are guaranteed by design, test, or statistical analysis.
Note 9:
If the product is in shutdown mode and V
DD exceeds 6V (to a max of 8V VDD) then most of the excess current will flow through the ESD protection circuits.
If the source impedance limits the current to a max of 10ma then the part will be protected. If the part is enabled when V
DD is above 6V circuit performance will
be curtailed or the part may be permanently damaged.
Note 10:
Human body model, 100pF discharged through a 1.5k
resistor, Pin 6 to ground.
External Components Description
Components
Functional Description
1.
R
I
Inverting input resistance which sets the closed-loop gain in conjunction with R
f. This resistor also forms a high-
pass filter with C
i at fc = 1/(2πRiCi).
2.
C
I
Input coupling capacitor which blocks the DC voltage at the amplifier's input terminals. Also creates a high-pass
filter with R
i at fc = 1/(2πRiCi). Refer to the section Proper Selection of External Components, for an explanation
of how to determine the value of C
i.
3.
R
f
Feedback resistance which sets the closed-loop gain in conjunction with R
i.
4.
C
S
Supply bypass capacitor which provides power supply filtering. Refer to the Power Supply Bypassing section for
information concerning proper placement and selection of the supply bypass capacitor.
www.national.com
4
LM4910