參數資料
型號： SAB88C166
廠商： SIEMENS A G
元件分類： 微控制器/微處理器
英文描述： 16-Bit CMOS Single-Chip Microcontrollers with/without oscillator prescaler with 32 KByte Flash EPROM
中文描述： 16-BIT, FLASH, 20 MHz, MICROCONTROLLER, PQFP100
文件頁數： 12/58頁
文件大小： 611K
代理商： SAB88C166
SAB 88C166(W)
Semiconductor Group
11
The selection of Flash Operation and Read Mode
is done via the three bits FWE, FEE and
FWMSET. The table below shows the combinations for these bits to select a specific function:
FWE enables/disables write operations, FEE selects erasing or programming, FWMSET controls
the writing mode. Bits FWE and FEE select an operation, but do not execute it directly.
Note:
Watch the FWMSET bit, when writing to register FCR (word access only), in order not to exit
Flash writing mode unintentionally by clearing bit FWMSET.
FBUSY:
This
read-only flag
is set to ‘1’ while a Flash programming or erasing operation is in
progress. FBUSY is set via hardware, when the respective command is issued.
RPROT:
This
write-only
Flash
Read Protection
bit determines whether Flash protection is active
or inactive. RPROT is the only FCR bit which can be modified even in the Flash standard mode but
only by an instruction executed from the on-chip Flash memory itself. Per reset, RPROT is set to ‘1’.
Note:
RPROT is only significant, if the general Flash memory protection is enabled.
FCVPP and VPPREV:
These
read-only
bits allow to monitor the V
PP
voltage. The Flash
Vpp
Revelation
bit VPPREV reflects the state of the V
PP
voltage in the Flash writing mode (VPPREV =
‘0’ indicates that V
PP
is below the threshold value necessary for reliable programming or erasure,
otherwise VPPREV = ‘1’). The Flash
Control V
PP
bit FCVPP indicates, if V
PP
fell below the valid
threshold value during a Flash programming or erase operation (FCVPP = ‘1’). FCVPP = ‘0’ after
such an operation indicates that no critical discontinuity on
V
PP
has occurred.
CKCTL:
This
Flash Timer Clock Control
bitfield controls the width of the programming or erase
pulses (TPRG) applied to Flash memory cells during the corresponding operation. The width of a
single programming or erase pulse and the cumulated programming or erase time must not exceed
certain values to avoid putting the Flash memory under critical stress (see table below).
FWMSET
FEE
FWE
Flash Operation Mode
Flash Read Mode
1
1
1
Erasing mode
Erase-Verify-Read via [Rn]
1
0
1
Programming mode
Program-Verify-Read via [Rn]
1
X
0
Non-Verify mode
Normal Read via [Rn]
0
X
X
Standard mode
Normal Read via [Rn] or mem
Time Specification
Maximum Programming Pulse Width
Maximum Cumulated Programming Time
Limit Value
128
2.5
μ
s
ms
Maximum Erase Pulse Width
Maximum Cumulated Erase Time
10
30
ms
s
相關PDF資料
PDF描述
SAB88C166-5M 16-Bit CMOS Single-Chip Microcontrollers with/without oscillator prescaler with 32 KByte Flash EPROM
SAE 81C90 16-Bit Microcontroller(16位微控制器)
SAE 81C91 16-bit microcontrollers(16位微控制器)
SAF-C167CR-16F 16-Bit CMOS Single-Chip Microcontroller with 128KByte Flash EPROM
SAFC167CR-16F 16-Bit CMOS Single-Chip Microcontroller with 128KByte Flash EPROM
相關代理商/技術參數
參數描述
SAB88C166-5M 制造商:INFINEON 制造商全稱:Infineon Technologies AG 功能描述:16-Bit CMOS Single-Chip Microcontrollers with/without oscillator prescaler with 32 KByte Flash EPROM
SAB88C166EVAL 制造商:Siemens 功能描述:
SAB88C166W-5M 制造商:INFINEON 制造商全稱:Infineon Technologies AG 功能描述:16-Bit CMOS Single-Chip Microcontrollers with/without oscillator prescaler with 32 KByte Flash EPROM
SAB9075H 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Picture-in-Picture PIP controller for NTSC
SAB9075HB-S 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Picture-in-Picture Circuit
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*