- 您現在的位置：買賣IC網 > PDF目錄385814 > SAB88C166-5M (SIEMENS A G) 16-Bit CMOS Single-Chip Microcontrollers with/without oscillator prescaler with 32 KByte Flash EPROM PDF資料下載
參數資料
| 型號： | SAB88C166-5M |
| 廠商： | SIEMENS A G |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 16-Bit CMOS Single-Chip Microcontrollers with/without oscillator prescaler with 32 KByte Flash EPROM |
| 中文描述： | 16-BIT, FLASH, 20 MHz, MICROCONTROLLER, PQFP100 |
| 文件頁數： | 5/58頁 |
| 文件大?。?/td> | 611K |
| 代理商： | SAB88C166-5M |
第1頁第2頁第3頁第4頁當前第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁
SAB 88C166(W)
Semiconductor Group
4
Pin Definitions and Functions
Symbol
Pin
Number
16 - 17
Input (I)
Output (O)
I/O
Function
P4.0 –
P4.1
16
17
O
O
Port 4 is a 2-bit bidirectional I/O port. It is bit-wise
programmable for input or output via direction bits. For a pin
configured as input, the output driver is put into high-
impedance state.
In case of an external bus configuration, Port 4 can be used to
output the segment address lines:
P4.0
A16
Least Significant Segment Addr. Line
P4.1
A17
Most Significant Segment Addr. Line
XTAL1
XTAL2
20
19
I
O
XTAL1:
Input to the oscillator amplifier and input to the
internal clock generator
Output of the oscillator amplifier circuit.
To clock the device from an external source, drive XTAL1,
while leaving XTAL2 unconnected. Minimum and maximum
high/low and rise/fall times specified in the AC Characteristics
must be observed.
XTAL2:
BUSACT,
EBC1,
EBC0
V
PP
RSTIN
22
23
24
23
I
I
I
External Bus Configuration selection inputs. These pins are
sampled during reset and select either the single chip mode
or one of the four external bus configurations:
BUSACT EBC1
EBC0
Mode/Bus Configuration
0
0
0
8-bit demultiplexed bus
0
0
1
8-bit multiplexed bus
0
1
0
16-bit muliplexed bus
0
1
1
16-bit demultiplexed bus
1
0
0
Single chip mode
1
0
1
Reserved.
1
1
0
Reserved.
1
1
1
Reserved.
After reset pin EBC1 accepts the programming voltage for the
Flash EPROM as an “alternate function”:
Flash EPROM Programming Voltage V
PP
= 12 V.
Reset Input with Schmitt-Trigger characteristics. A low level at
this pin for a specified duration while the oscillator is running
resets the SAB 88C166(W). An internal pullup resistor permits
power-on reset using only a capacitor connected to
V
SS
.
Internal Reset Indication Output. This pin is set to a low level
when the part is executing either a hardware-, a software- or a
watchdog timer reset. RSTOUT remains low until the EINIT
(end of initialization) instruction is executed.
27
I
RSTOUT 28
O
相關PDF資料 |
PDF描述 |
|---|---|
| SAE 81C90 | 16-Bit Microcontroller(16位微控制器) |
| SAE 81C91 | 16-bit microcontrollers(16位微控制器) |
| SAF-C167CR-16F | 16-Bit CMOS Single-Chip Microcontroller with 128KByte Flash EPROM |
| SAFC167CR-16F | 16-Bit CMOS Single-Chip Microcontroller with 128KByte Flash EPROM |
| SAF-C503 | 8-Bit CMOS Microcontroller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SAB88C166EVAL | 制造商:Siemens 功能描述: |
| SAB88C166W-5M | 制造商:INFINEON 制造商全稱:Infineon Technologies AG 功能描述:16-Bit CMOS Single-Chip Microcontrollers with/without oscillator prescaler with 32 KByte Flash EPROM |
| SAB9075H | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Picture-in-Picture PIP controller for NTSC |
| SAB9075HB-S | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Picture-in-Picture Circuit |
| SAB9076H | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Picture-In-Picture PIP controller |
發布緊急采購，3分鐘左右您將得到回復。