參數資料
型號： SAB83C515A-5
廠商： INFINEON TECHNOLOGIES AG
元件分類： 8位微控制器
英文描述： 8-Bit CMOS Single-Chip Microcontroller
中文描述： 8位CMOS單芯片微控制器
文件頁數： 36/57頁
文件大?。?/td> 899K
代理商： SAB83C515A-5
SAB 80C515A/83C515A-5
Semiconductor Group
35
Requirements for Hardware Power Down Mode
There is no dedicated pin to enable the Hardware Power Down Mode. The control pin PE/SWD
has no control function in this mode. It enables and disables only the use of software controlled
power saving modes.
Software Controlled Power Saving Modes
All of these modes are entered by software. Special function register PCON (power control
register, address is 87
H
) is used to select one of these modes.
Slow Down Mode
During slow down operation all signal frequencies that are derived from the oscillator clock, are
divided by eight, also the clockout signal and and the watchdog timer count.
The slow down mode is enabled by setting bit SD. The controller actually enters the slow down
mode after a short synchronisation period (max. 2 machine cycles).
The slow down mode is disabled by clearing bit SD.
Idle Mode
During idle mode all peripherals of the SAB 80C515A (except for the watchdog timer) are still
supplied by the oscillator clock. Thus the user has to take care which peripheral should
continue to run and which has to be stopped during Idle.
The procedure to enter the Idle mode is similar to the one entering the power down mode. The
two bits IDLE and IDLS must be set by two consecutive instructions to minimize the chance of
unintentional activating of the idle mode.
There are two ways to terminate the idle mode:
– The idle mode can be terminated by activating any enabled interrupt. This interrupt will be
serviced and the instruction to be executed following the RETI instruction will be the one
following the instruction that set the bit IDLS.
– The other way to terminate the idle mode, is a hardware reset. Since the oscillator is still
running, the hardware reset must be held active only for two machine cycles for a complete
reset.
Normally the port pins hold the logical state they had at the time idle mode was activated. If
some pins are programmed to serve their alternate functions they still continue to output during
idle mode if the assigned function is on. The control signals ALE and PSEN hold at logic high
levels (see table 5).
相關PDF資料
PDF描述
SAB80C515A 8-Bit CMOS Single-Chip Microcontroller Family
SAB80C515A-5 8-Bit CMOS Single-Chip Microcontroller Family
SAB80C515A-M18-T3 8-Bit CMOS Single-Chip Microcontroller
SAB83C515A-5M18-T3 8-Bit CMOS Single-Chip Microcontroller
SAB83C515A-5N18
相關代理商/技術參數
參數描述
SAB83C515A-5M18-T3 制造商:INFINEON 制造商全稱:Infineon Technologies AG 功能描述:8-Bit CMOS Single-Chip Microcontroller
SAB83C515A-5N18 制造商:Siemens 功能描述:8-BIT, MROM, 18 MHz, MICROCONTROLLER, PQCC68
SAB83C515A-5N18-T3 制造商:INFINEON 制造商全稱:Infineon Technologies AG 功能描述:8-Bit CMOS Single-Chip Microcontroller
SAB83C517A-5 制造商:INFINEON 制造商全稱:Infineon Technologies AG 功能描述:8-Bit CMOS Single-Chip Microcontroller
SAB83C517A-5N18 制造商:INFINEON 制造商全稱:Infineon Technologies AG 功能描述:8-Bit CMOS Single-Chip Microcontroller
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*