參數資料
型號: SAB80C515A-N18
廠商: SIEMENS A G
元件分類: 微控制器/微處理器
英文描述: 8-Bit CMOS Single-Chip Microcontroller
中文描述: 8-BIT, 18 MHz, MICROCONTROLLER, PQCC68
封裝: PLASTIC, LCC-68
文件頁數: 37/57頁
文件大?。?/td> 899K
代理商: SAB80C515A-N18
SAB 80C515A/83C515A-5
Semiconductor Group
36
Software Power Down Mode
The power down mode is entered by two consecutive instructions directly following each other.
The first instruction has to set the flag PDE (power down enable) and must not set PDS (power
down set). The following instruction has to set the start bit PDS. Bits PDE and PDS will
automatically be cleared after having been set.
The instruction that sets bit PDS is the last instruction executed before going into power down
mode. The only exit from power down mode is a hardware reset.
The status of all output lines of the controller can be looked up in table 5.
Hardware Controlled Power Down Mode
The pin
HWPD controls this mode. If it is on logic high level (inactive) the part is running in the
normal operating modes. If pin HWPD gets active (low level) the part enters the Hardware
Power Down Mode; this is independent of the state of pin
PE/SWD.
HWPD is sampled once per machine cycle. If it is found active, the device starts a complete
internal reset sequence. The watchdog timer is stopped and its status flag WDTS is cleared
exactly the same effects as a hardware reset. In this phase the power consumption is not yet
reduced. After completion of the internal reset both oscillators of the chip are disabled. At the
same time the port pins and several control lines enter a floating state as shown in table 5. In
this state the power consumption is reduced to the power down current IPD. Also the supply
voltage can be reduced. Table 5 also lists the voltages which may be applied at the pins during
Hardware Power Down Mode without affecting the low power consumption.
Termination of HWPD Mode:
This power down state is maintained while pin HWPD is held active. If HWPD goes to high level
(inactive state) an automatic start up procedure is performed:
– First the pins leave their floating condition and enter their default reset state (as they had
immediately before going to float state).
– Both oscillators are enabled. The oscillator watchdog’s RC oscillator starts up very fast (typ.
less than 2 ms).
– Because the oscillator watchdog is active it detects a failure condition if the on-chip oscillator
hasn’t yet started. Hence, the watchdog keeps the part in reset and supplies the internal
clock from the RC oscillator.
– Finally, when the on-chip oscillator has started, the oscillator watchdog releases the part
from reset with oscillator watchdog status flag set.
When automatic start of the watchdog was enabled (PE/SWD connected to
V
CC
),
the
Watchdog Timer will start, too (with its default reload value for time-out period).
– The
Reset pin overrides the Hardware Power Down function, i.e. if reset gets active during
Hardware Power Down it is terminated and the device performs the normal
resetfunction.(Thus, pin
Reset has to be inactive during Hardware Power Down Mode).
function.(Thus, pin
Reset has to be inactive during Hardware Power Down Mode).
相關PDF資料
PDF描述
SAB80C515A-N18-T3 8-Bit CMOS Single-Chip Microcontroller
SAB80C517A-M18 8-Bit CMOS Single-Chip Microcontroller
SAB80C517A 8-Bit CMOS Single-Chip Microcontroller
SAB83C517A-5 8-Bit CMOS Single-Chip Microcontroller
SAB83C517A-5N18-T3
相關代理商/技術參數
參數描述
SAB80C515A-N18-T3 制造商:INFINEON 制造商全稱:Infineon Technologies AG 功能描述:8-Bit CMOS Single-Chip Microcontroller
SAB80C515AN18T4TR 制造商:Infineon Technologies AG 功能描述:MCU 8-bit C500 8051 CISC ROMLess 5V 68-Pin PLCC
SAB80C515-M 制造商:INFINEON 制造商全稱:Infineon Technologies AG 功能描述:8-Bit CMOS Single-Chip Microcontroller
SAB80C515-M-T40/85 制造商:INFINEON 制造商全稱:Infineon Technologies AG 功能描述:8-Bit CMOS Single-Chip Microcontroller
SAB80C515-N 制造商:INFINEON 制造商全稱:Infineon Technologies AG 功能描述:8-Bit CMOS Single-Chip Microcontroller