參數資料
型號: S8361
廠商: Electronic Theatre Controls, Inc.
英文描述: POSITION SENSITIVE DETECTOR
中文描述: 位置靈敏探測器
文件頁數: 13/16頁
文件大小: 1289K
代理商: S8361
10
Figure 6-1 Response wavelength example of PSD
KPSDC0078EB
2) Diffusion time t
2
of carriers generated outside the deple-
tion layer
Carriers are also generated outside the depletion layer
when light is absorbed in the PSD chip surrounding areas
outside the active area or at locations deeper than the de-
pletion layer in the substrate. These carriers diffuse through
the substrate and are extracted as an output. The time t
2
required for these carriers to diffuse may be more than sev-
eral microseconds.
The equation below gives the approximate rise time tr of a
PSD. Figure 6-1 shows typical output waveforms in re-
sponse to stepped light input.
Figure 6-2 shows the relation between the rise time and re-
verse voltage measured at different wavelengths. The rise
time can be reduced by increasing the reverse voltage and
using a light beam of shorter wavelengths. Selecting a PSD
with a small Rie is also effective in improving the rise time.
Figure 6-2 Rise time vs. reverse voltage (S4583-06)
A method for integrating position signals can be used when
detecting pulsed light having a pulse width shorter than the
PSD rise time.
Characteristic and use
6. Response speed
As with photodiodes, the response speed of PSD is the
time required for the generated carriers to be extracted as
current by an external circuit. This is generally expressed
as the rise time tr and is an important parameter when de-
tecting a spot light traveling over the active surface at high
speeds or using pulse-modulated light for subtracting the
background light. The rise time is defined as the time need-
ed for the output signal to rise from 10 to 90 % of its peak
value and is chiefly determined by the following two factors.
1) Time constant t
1
determined by the interelectrode resist-
ance, load resistance and terminal capacitance
The interelectrode resistance Rie of PSD basically acts as
load resistance R
L
, so the time constant t
1
is given by the
interelectrode resistance Rie and terminal capacitance Ct,
as follows:
t
1
= 2.2 . Ct . (Rie + R
L
) ......... (6-1)
The rise time listed in our PSD datasheets is measured
with a spot light striking the center of the active area with
the interelectrode resistance Rie distributed between the
electrodes. So the time constant t
1
is as follows:
t
1
= 0.5 . Ct . (Rie + R
L
) ......... (6-2)
KPSDB0110EA
REVERSE VOLTAGE (V)
(Typ. Ta=25
C)
R
1
0.1
0
10
8
6
4
2
10
100
l
=890 nm
l
=650 nm
t
12
+ t
22
.................... (6-3)
tr
LIGHT INPUT
OUTPUT WAVEFORM
(t
1
>>t
2
)
OUTPUT WAVEFORM
(t
2
>>t
1
)
相關PDF資料
PDF描述
S8380 NMOS linear image sensor NMOS linear image sensors with high IR sensitivity
S8380-128Q NMOS linear image sensor NMOS linear image sensors with high IR sensitivity
S8380-256Q NMOS linear image sensor NMOS linear image sensors with high IR sensitivity
S8380-512Q NMOS linear image sensor NMOS linear image sensors with high IR sensitivity
S8381-1024Q NMOS linear image sensor NMOS linear image sensors with high IR sensitivity
相關代理商/技術參數
參數描述
S-8363B-I6T1U2 制造商:Seiko Instruments Inc (SII) 功能描述:STEP SWR 1.2MHZ PWM/PFM
S-8365 制造商:SII 制造商全稱:Seiko Instruments Inc 功能描述:STEP-UP, SUPER-SMALL PACKAGE, 1.2 MHz PWM CONTROL or PWM/PFM SWITCHABLE SWITCHING REGULATOR CONTROLLER
S-8365AAAAA-I6T1G2 制造商:Seiko Instruments Inc (SII) 功能描述:STEP-UP SWR 1.2MHZ PWM/PFM
S-8365AAAAA-M5T1S2 制造商:Seiko Instruments Inc (SII) 功能描述:STEP-UP SWR 1.2MHZ PWM/PFM
S-8365AAABA-I6T1U2 功能描述:IC REG CTRLR BOOST SNT-6A 制造商:ablic u.s.a. inc. 系列:- 包裝:剪切帶(CT) 零件狀態:在售 輸出類型:晶體管驅動器 功能:升壓 輸出配置:正 拓撲:升壓 輸出數:1 輸出階段:1 電壓 - 電源(Vcc/Vdd):1.8 V ~ 5.5 V 頻率 - 開關:1.2MHz 占空比(最大):0.9 同步整流器:無 時鐘同步:無 串行接口:- 控制特性:- 工作溫度:-40°C ~ 85°C(TA) 封裝/外殼:6-SMD,扁平引線 供應商器件封裝:SNT-6A 標準包裝:1