參數資料
型號： S29AL016M90TAIR13
廠商： SPANSION LLC
元件分類： DRAM
英文描述： 16 MEGABIT (2M X 8 BIT / I M X 16 BIT) 3.0 VOLT ONLY BOOT SECTOR FLASH MEMORY
中文描述： 1M X 16 FLASH 3V PROM, 90 ns, PDSO48
封裝： MO-142DD, TSOP-48
文件頁數： 23/59頁
文件大?。?/td> 1917K
代理商： S29AL016M90TAIR13
April 21, 2004 S29AL016M_00A4
S29AL016M
24
Logical Inhibit
Write cycles are inhibited by holding any one of OE# = V
IL
, CE# = V
IH
or WE# =
V
IH
. To initiate a write cycle, CE# and WE# must be a logical zero while OE# is a
logical one.
Power-Up Write Inhibit
If WE# = CE# = V
IL
and OE# = V
IH
during power up, the device does not accept
commands on the rising edge of WE#. The internal state machine is automatically
reset to reading array data on power-up.
Command Definitions
Writing specific address and data commands or sequences into the command
register initiates device operations. Tables
10
–
11
define the valid register com-
mand sequences.
Note that writing incorrect address and data values or writing
them in the improper sequence may place the device in an unknown state. A
reset command is then required to set the device for the next operation.
All addresses are latched on the falling edge of WE# or CE#, whichever happens
later. All data is latched on the rising edge of WE# or CE#, whichever happens
first. Refer to the appropriate timing diagrams in the
“AC Characteristics”
section.
Reading Array Data
The device is automatically set to reading array data after device power-up. No
commands are required to retrieve data. The device is also ready to read array
data after completing an Embedded Program or Embedded Erase algorithm.
After the device accepts an Erase Suspend command, the device enters the
Erase Suspend mode. The system can read array data using the standard read
timings, except that if it reads at an address within erase-suspended sectors,
the device outputs status data. After completing a programming operation in
the Erase Suspend mode, the system may once again read array data with the
same exception. See
“Erase Suspend/Erase Resume Commands”
for more in-
formation on this mode.
The system
must
issue the reset command to re-enable the device for reading
array data if DQ5 goes high, or while in the autoselect mode. See the
“Reset Com-
mand”
section, next.
See also
“Requirements for Reading Array Data”
in the
“Device Bus Operations”
section for more information. The
Read Operations
table provides the read pa-
rameters, and
Figure 13
shows the timing diagram.
Reset Command
Writing the reset command to the device resets the device to reading array data.
Address bits are don’t care for this command.
The reset command may be written between the sequence cycles in an erase
command sequence before erasing begins. This resets the device to reading array
data. Once erasure begins, however, the device ignores reset commands until the
operation is complete.
The reset command may be written between the sequence cycles in a program
command sequence before programming begins. This resets the device to read-
ing array data (also applies to programming in Erase Suspend mode). Once
programming begins, however, the device ignores reset commands until the op-
eration is complete.
相關PDF資料
PDF描述
S29AL016M90TAIR20 16 MEGABIT (2M X 8 BIT / I M X 16 BIT) 3.0 VOLT ONLY BOOT SECTOR FLASH MEMORY
S29AL016M90TAIR22 16 MEGABIT (2M X 8 BIT / I M X 16 BIT) 3.0 VOLT ONLY BOOT SECTOR FLASH MEMORY
S29AL016M90TAIR23 16 MEGABIT (2M X 8 BIT / I M X 16 BIT) 3.0 VOLT ONLY BOOT SECTOR FLASH MEMORY
S29AL016M90TFI010 16 MEGABIT (2M X 8 BIT / I M X 16 BIT) 3.0 VOLT ONLY BOOT SECTOR FLASH MEMORY
S29AL016M90TFI012 16 MEGABIT (2M X 8 BIT / I M X 16 BIT) 3.0 VOLT ONLY BOOT SECTOR FLASH MEMORY
相關代理商/技術參數
參數描述
S29AL016M90TAIR20 制造商:SPANSION 制造商全稱:SPANSION 功能描述:16 MEGABIT (2M X 8 BIT / I M X 16 BIT) 3.0 VOLT ONLY BOOT SECTOR FLASH MEMORY
S29AL016M90TAIR22 制造商:SPANSION 制造商全稱:SPANSION 功能描述:16 MEGABIT (2M X 8 BIT / I M X 16 BIT) 3.0 VOLT ONLY BOOT SECTOR FLASH MEMORY
S29AL016M90TAIR23 制造商:SPANSION 制造商全稱:SPANSION 功能描述:16 MEGABIT (2M X 8 BIT / I M X 16 BIT) 3.0 VOLT ONLY BOOT SECTOR FLASH MEMORY
S29AL016M90TFI010 制造商:SPANSION 制造商全稱:SPANSION 功能描述:16 Megabit (2 M x 8-Bit/1 M x 16-Bit) 3.0 Volt-only Boot Sector Flash Memory Featuring MirrorBit⑩ Technology
S29AL016M90TFI012 制造商:SPANSION 制造商全稱:SPANSION 功能描述:16 MEGABIT (2M X 8 BIT / I M X 16 BIT) 3.0 VOLT ONLY BOOT SECTOR FLASH MEMORY
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*