參數資料
型號： S29AL016M10BAIR10
廠商： SPANSION LLC
元件分類： DRAM
英文描述： Successive Approximation Registers; Package: SO-16 WB; No of Pins: 16; Container: Tape and Reel; Qty per Container: 1000
中文描述： 1M X 16 FLASH 3V PROM, 100 ns, PBGA48
封裝： 6 X 8 MM, FBGA-48
文件頁數： 24/59頁
文件大?。?/td> 1917K
代理商： S29AL016M10BAIR10
25
S29AL016M
S29AL016M_00A4 April 21, 2004
The reset command may be written between the sequence cycles in an autoselect
command sequence. Once in the autoselect mode, the reset command
must
be
written to return to reading array data (also applies to autoselect during Erase
Suspend).
If DQ5 goes high during a program or erase operation, writing the reset command
returns the device to reading array data (also applies during Erase Suspend).
Autoselect Command Sequence
The autoselect command sequence allows the host system to access the manu-
facturer and devices codes, and determine whether or not a sector is protected.
Tables
10
–
11
show the address and data requirements. This method is an alter-
native to that shown in Table
4
, which is intended for PROM programmers and
requires V
ID
on address bit A9.
The autoselect command sequence is initiated by writing two unlock cycles, fol-
lowed by the autoselect command. The device then enters the autoselect mode,
and the system may read at any address any number of times, without initiating
another command sequence.
A read cycle at address XX00h retrieves the manufacturer code. A read cycle at
address XX01h returns the device code. A read cycle containing a sector address
(SA) and the address XX02h in word mode (or XX04h in byte mode) returns
XX01h if that sector is protected, or 00h if it is unprotected. Refer to Tables
2
and
3
for valid sector addresses.
The system must write the reset command to exit the autoselect mode and return
to reading array data.
Word/Byte Program Command Sequence
The system may program the device by word or byte, depending on the state
of the BYTE# pin. Programming is a four-bus-cycle operation. The program
command sequence is initiated by writing two unlock write cycles, followed by
the program set-up command. The program address and data are written next,
which in turn initiate the Embedded Program algorithm. The system is
not
re-
quired to provide further controls or timings. The device automatically
generates the program pulses and verifies the programmed cell margin. Tables
10
–
11
show the address and data requirements for the program command se-
quence.
Note that the SecSi Sector, autoselect, and CFI functions are
unavailable when a program operation is in progress.
When the Embedded Program algorithm is complete, the device then returns to
reading array data and addresses are no longer latched. The system can deter-
mine the status of the program operation by using DQ7, DQ6, or RY/BY#. See
“Write Operation Status”
for information on these status bits.
Any commands written to the device during the Embedded Program Algorithm
are ignored. Note that a
hardware reset
immediately terminates the program-
ming operation. The Program command sequence should be reinitiated once the
device has reset to reading array data, to ensure data integrity.
Programming is allowed in any sequence and across sector boundaries. Program-
ming to the same address multiple times without intervening erases is limited.
For such application requirements, please contact your local Spansion represen-
tative.
Any bit in a word or byte
cannot be programmed from “0” back to a
“1”.
Attempting to do so may halt the operation and set DQ5 to “1,” or cause the
Data# Polling algorithm to indicate the operation was successful. However, a suc-
相關PDF資料
PDF描述
S29AL016M10BAIR12 Successive Approximation Registers; Package: SO-16 WB; No of Pins: 16; Container: Tape and Reel; Qty per Container: 1000
S29AL016M10BAIR13 Quad 2-Channel Analog Multiplexer/Demultiplexer; Package: PDIP-16; No of Pins: 16; Container: Rail; Qty per Container: 500
S29AL016M10BAIR20 Quad 2-Channel Analog Multiplexer/Demultiplexer; Package: PDIP-16; No of Pins: 16; Container: Rail; Qty per Container: 500
S29AL016M10BAIR22 Quad 2-Channel Analog Multiplexer/Demultiplexer; Package: SOIC 16 LEAD; No of Pins: 16; Container: Rail; Qty per Container: 48
S29AL016M10BAIR23 Quad 2-Channel Analog Multiplexer/Demultiplexer; Package: SOIC 16 LEAD; No of Pins: 16; Container: Rail; Qty per Container: 48
相關代理商/技術參數
參數描述
S29AL016M10BAIR12 制造商:SPANSION 制造商全稱:SPANSION 功能描述:16 MEGABIT (2M X 8 BIT / I M X 16 BIT) 3.0 VOLT ONLY BOOT SECTOR FLASH MEMORY
S29AL016M10BAIR13 制造商:SPANSION 制造商全稱:SPANSION 功能描述:16 Megabit (2 M x 8-Bit/1 M x 16-Bit) 3.0 Volt-only Boot Sector Flash Memory Featuring MirrorBit⑩ Technology
S29AL016M10BAIR20 制造商:SPANSION 制造商全稱:SPANSION 功能描述:16 MEGABIT (2M X 8 BIT / I M X 16 BIT) 3.0 VOLT ONLY BOOT SECTOR FLASH MEMORY
S29AL016M10BAIR22 制造商:SPANSION 制造商全稱:SPANSION 功能描述:16 Megabit (2 M x 8-Bit/1 M x 16-Bit) 3.0 Volt-only Boot Sector Flash Memory Featuring MirrorBit⑩ Technology
S29AL016M10BAIR23 制造商:SPANSION 制造商全稱:SPANSION 功能描述:16 MEGABIT (2M X 8 BIT / I M X 16 BIT) 3.0 VOLT ONLY BOOT SECTOR FLASH MEMORY
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*