參數資料
型號: S216S02F
廠商: Sharp Corporation
英文描述: IT(rms)÷16A, Zero Cross type SIP 4pin Triac output SSR
中文描述: 資訊科技(有效值)÷ 16A條,零交叉式園區4芯晶閘管輸出蘇維埃社會主義共和國
文件頁數: 9/13頁
文件大?。?/td> 242K
代理商: S216S02F
9
S116S02 Series
S216S02 Series
For additional design assistance, please review our corresponding Optoelectronic Application Notes.
Standard Circuit
Tr1
R
1
D
1
V
1
+
V
CC
AC Line
Load
Z
S
Z
S
: Surge absorption circuit (Snubber circuit)
SSR
3
4
2
1
S116S02
S216S02
Sheet No.: D4-A02701EN
Degradation
In general, the emission of the IRED used in SSR will degrade over time.
In the case where long term operation and / or constant extreme temperature fluctuations will be applied to
the devices, please allow for a worst case scenario of 50% degradation over 5years.
Therefore in order to maintain proper operation, a design implementing these SSRs should provide at least
twice the minimum required triggering current from initial operation.
(a) Make sure there are no warps or bumps on the heat sink, insulation sheet and device surface.
(b) Make sure there are no metal dusts or burrs attached onto the heat sink, insulation sheet and device sur-
face.
(c) Make sure silicone grease is evenly spread out on the heat sink, insulation sheet and device surface.
Silicone grease to be used is as follows;
1) There is no aged deterioration within the operating temperature ranges.
2) Base oil of grease is hardly separated and is hardly permeated in the device.
3) Even if base oil is separated and permeated in the device, it should not degrade the function of a device.
Recommended grease : G-746 (Shin-Etsu Chemical Co., Ltd.)
: G-747 (Shin-Etsu Chemical Co., Ltd.)
: SC102 (Dow Corning Toray Silicone Co., Ltd.)
In case the optional heat sink is screwed up, please solder after screwed.
In case of the lead frame bending, please keep the following minimum distance and avoid any mechanical
stress between the base of terminals and the molding resin.
Some of AC electromagnetic counters or solenoids have built-in rectifier such as the diode.
In this case, please use the device carefully since the load current waveform becomes similar with rectangu-
lar waveform and this results may not make a device turn off.
4.4mm MIN.
相關PDF資料
PDF描述
S21MA01 6-pin DIP Type SSR for Low Power Control
S21MD10T High Speed, High Sensitivity Type Phototriac Coupler
S21MD3 High Noise Resistance Type Phototriac Coupler
S21MD3TV High Noise-resistance Type Phototriac Coupler
S21MD3V High Noise Resistance Type Phototriac Coupler
相關代理商/技術參數
參數描述
S216SE1 功能描述:RELAY SSR 240VAC 16A TRIAC 4-SIP RoHS:否 類別:繼電器 >> 固態 系列:S216 其它有關文件:AQx REACH Cert of Compliance 特色產品:AQY Series Relays 標準包裝:1 系列:PhotoMOS™ AQY 電路:SPST-NO(1 Form A) 輸出類型:AC,DC(RF) 導通狀態電阻:1.25 歐姆 負載電流:250mA 輸入電壓:1.3VDC 電壓 - 負載:0 ~ 40 V 安裝類型:表面貼裝 端接類型:SMD(SMT)接片 封裝/外殼:4-SMD(0.175",4.45mm) 供應商設備封裝:4-SSOP 包裝:Digi-Reel® 繼電器類型:繼電器 其它名稱:255-2683-6
S216SE1F 功能描述:固態繼電器-PCB安裝 4-SIP NON-ZC 8mA RoHS:否 制造商:Omron Electronics 控制電壓范圍: 負載電壓額定值:40 V 負載電流額定值:120 mA 觸點形式:1 Form A (SPST-NO) 輸出設備:MOSFET 封裝 / 箱體:USOP-4 安裝風格:SMD/SMT
S216SE2 功能描述:RELAY SSR 240VAC 16A ZC 4-SIP RoHS:否 類別:繼電器 >> 固態 系列:S216 其它有關文件:AQx REACH Cert of Compliance 特色產品:AQY Series Relays 標準包裝:1 系列:PhotoMOS™ AQY 電路:SPST-NO(1 Form A) 輸出類型:AC,DC(RF) 導通狀態電阻:1.25 歐姆 負載電流:250mA 輸入電壓:1.3VDC 電壓 - 負載:0 ~ 40 V 安裝類型:表面貼裝 端接類型:SMD(SMT)接片 封裝/外殼:4-SMD(0.175",4.45mm) 供應商設備封裝:4-SSOP 包裝:Digi-Reel® 繼電器類型:繼電器 其它名稱:255-2683-6
S216SE2F 功能描述:固態繼電器-PCB安裝 4-SIP ZERO-C 8mA RoHS:否 制造商:Omron Electronics 控制電壓范圍: 負載電壓額定值:40 V 負載電流額定值:120 mA 觸點形式:1 Form A (SPST-NO) 輸出設備:MOSFET 封裝 / 箱體:USOP-4 安裝風格:SMD/SMT
S216ULCSAD 制造商:Panasonic Electric Works 功能描述: