- 您現在的位置：買賣IC網 > PDF目錄374644 > S16MD01 (Sharp Corporation) 8-Pin DIP Type SSR for Low Power Control PDF資料下載
參數資料
| 型號： | S16MD01 |
| 廠商： | Sharp Corporation |
| 英文描述： | 8-Pin DIP Type SSR for Low Power Control |
| 中文描述： | 8引腳DIP型蘇維埃社會主義共和國低功率控制 |
| 文件頁數： | 4/4頁 |
| 文件大?。?/td> | 66K |
| 代理商： | S16MD01 |
S16MD01/S16MD02/S26MD01/S26MD02
Forward current I
F
(mA)
T
o
μ
3
4
5
10
20
30
40
50
100
2
10
20
Ambient temperature T
a
(C)
Z
O
- 30
0
20
40
60
80
100
15
20
25
Load
Z
S
SSR
2
3
8
6
D
1
R
1
+
V
CC
(1) DC Drive
(2) Pulse Drive
I
Basic Operation Circuit
Fig.11 Turn-on Time vs. Forward Current
(S16MD02/S26MD02)
Fig.12 Zero-cross Voltage vs.
Ambient Temperature
Z
S
:
Surge absorption circuit
I
Precautions for Use
1) All pins must be soldered since they are also used as heat sinks (heat radiation fins). In
designing, consider the heat radiation from the mounted SSR.
2) For higher radiation efficiency that allows wider thermal margin, secure a wider round
pattern for Pin No.8 when designing mounting pattern. The rounded part of Pin No.5 (gate)
must be as small as possible. Pulling the gate pattern around increases the change of being
affected by external noise.
3) As for other general cautions, refer to the chapter“Precautions for Use”
(S16MD02/S26MD02)
AC 100V (
S16MD01/S16MD02
)
AC 200V (
S26MD01/S26MD02
)
Notes 1 ) If large amount of surge is loaded onto V
CC
or the driver circuit, add a diode D
1
between terminal 2
and 3 to prevent reverse bias from being applied to the infrared LED.
2 ) Be sure to install a surge absorption circuit.
An appropriate circuit must be chosen according to the load (for CR, choose its constant ). This must be
carefully done especially for an inductive load.
3 ) For phase control, adjust such that the load current immediately after the input signal is applied will be
more than 30mA.
V
I
Tr1
Load : R
I
F
= 15mA
AC supply voltage
Input signal
Load current
(for resistance load)
(3) Phase Control
V
D
= 6V
R
L
= 100
T
a
= 25C
相關PDF資料 |
PDF描述 |
|---|---|
| S16MD02 | 8-Pin DIP Type SSR for Low Power Control |
| S175-28 | 175 WATTS 28 VOLTS 1.5-30 MHZ HF COMMUNICATIONS |
| S1880 | MR Series Rocker, 1 lamp circuit (Clear Red) miniature rectangle housing, SPDT, 2 position, Quick-connect, Snap-in panel, Silver alloy contacts |
| S1881 | MR Series Rocker, 1 lamp circuit (Clear Green) miniature rectangle housing, SPDT, 2 position, Quick-connect, Snap-in panel, Silver alloy contacts |
| S1300 | POSITION SENSITIVE DETECTOR |
相關代理商/技術參數 |
參數描述 |
|---|---|
| S16MD02 | 制造商:SHARP 制造商全稱:Sharp Electrionic Components 功能描述:8-Pin DIP Type SSR for Low Power Control |
| S16MR | 功能描述:整流器 1000V 16A REV Leads Std. Recovery RoHS:否 制造商:Vishay Semiconductors 產品:Standard Recovery Rectifiers 配置: 反向電壓:100 V 正向電壓下降: 恢復時間:1.2 us 正向連續電流:2 A 最大浪涌電流:35 A 反向電流 IR:5 uA 安裝風格:SMD/SMT 封裝 / 箱體:DO-221AC 封裝:Reel |
| S16MSD2 | 制造商:Diotec 功能描述:Bulk |
| S16N1.5F2-B | 制造商:TE Connectivity 功能描述: |
| S16N1.8F2-B | 制造商:TE Connectivity 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。