- 您現在的位置：買賣IC網 > PDF目錄374641 > S-93C56AMFN (Electronic Theatre Controls, Inc.) CMOS SERIAL E2PROM PDF資料下載
參數資料
| 型號： | S-93C56AMFN |
| 廠商： | Electronic Theatre Controls, Inc. |
| 英文描述： | CMOS SERIAL E2PROM |
| 中文描述： | 的CMOS串行E2PROM |
| 文件頁數： | 7/53頁 |
| 文件大小： | 214K |
| 代理商： | S-93C56AMFN |
第1頁第2頁第3頁第4頁第5頁第6頁當前第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁
CMOS SERIAL E
2
PROM
S-93C46A
/
56A
/
66A
Seiko Instruments Inc.
6
n
Operation
Instructions (in the order of start-bit, instruction, address, and data) are latched to DI in synchronization with the rising
edge of SK after CS goes high. A start-bit can only be recognized when the high of DI is latched to the rising edge of SK
when CS goes from low to high, it is impossible for it to be recognized as long as DI is low, even if there are SK pulses after
CS goes high. Any SK pulses input while DI is low are called "dummy clocks." Dummy clocks can be used to adjust the
number of clock cycles needed by the serial IC to match those sent out by the CPU. Instruction input finishes when CS
goes low, where it must be low between commands during t
CDS
.
All input, including DI and SK signals, is ignored while CS is low, which is stand-by mode.
1. Read
The READ instruction reads data from a specified address. After A0 is latched at the rising edge of SK, DO output
changes from a high-impedance state (Hi-Z) to low level output. Data is continuously output in synchronization with the rise
of SK.
When all of the data (D0) in the specified address has been read, the data in the next address can be read with the input
of another SK clock. Thus, it is possible for all of the data addresses to be read through the continuous input of SK clocks
as long as CS is high.
The last address (An
A1 A0 = 1
11) rolls over to the top address (An
A1 A0 = 0
00).
Figure 5
Read Timing (S-93C56A)
Figure 4
Read Timing (S-93C46A)
A
5
A
4
A
3
A
2
A
1
A
0
+1
A
5
A
4
A
3
A
2
A
1
A
0
+2
D
15
D
15
D
14
D
14
D
13
D
14
Hi-Z
D
13
D
0
D
1
D
2
D
15
0
Hi-Z
A
0
A
1
A
2
A
3
A
4
A
5
0
1
1
28
27
26
25
24
23
12
11
10
9
8
7
6
5
4
3
2
1
44
43
42
41
40
39
D
13
D
0
D
1
D
2
CS
SK
DI
DO
A
0
A
6
12
45
29
14
D
15
D
15
D
14
D
14
D
13
D
14
Hi-Z
A
6
A
5
A
4
A
3
A
2
A
1
A
0
+1
D
13
D
0
D
1
D
2
D
15
0
Hi-Z
A
1
A
2
A
3
A
4
A
5
X
0
1
1
28
27
26
25
24
11
10
9
8
7
6
5
4
3
2
1
44
43
42
41
40
A
6
A
5
A
4
A
3
A
2
A
1
A
0
+2
D
13
D
0
D
1
13
CS
SK
DI
DO
相關PDF資料 |
PDF描述 |
|---|---|
| S-93C66A | CMOS SERIAL E2PROM |
| S-93C66ADFJ | CMOS SERIAL E2PROM |
| S-93C66ADP | CMOS SERIAL E2PROM |
| S-93C66AFJ | CMOS SERIAL E2PROM |
| S-93C66AFT | CMOS SERIAL E2PROM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| S-93C56AMFN-TB | 功能描述:電可擦除可編程只讀存儲器 2K (128X16) Hi-Speed RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
| S-93C56B | 制造商:SII 制造商全稱:Seiko Instruments Inc 功能描述:CMOS SERIAL E2PROM |
| S-93C56BD0H-D8S1G | 制造商:SII 制造商全稱:Seiko Instruments Inc 功能描述:CMOS SERIAL E2PROM |
| S-93C56BD0H-I8T1G | 制造商:SII 制造商全稱:Seiko Instruments Inc 功能描述:CMOS SERIAL E2PROM |
| S-93C56BD0H-J8T1G | 制造商:SII 制造商全稱:Seiko Instruments Inc 功能描述:CMOS SERIAL E2PROM |
發布緊急采購，3分鐘左右您將得到回復。