- 您現在的位置：買賣IC網 > PDF目錄385780 > RT9198A-16PU5R (Richtek Technology Corporation) 300mA, Low Noise, Ultra-Fast CMOS LDO Regulator PDF資料下載
參數資料
| 型號： | RT9198A-16PU5R |
| 廠商： | Richtek Technology Corporation |
| 元件分類： | 穩壓器 |
| 英文描述： | 300mA, Low Noise, Ultra-Fast CMOS LDO Regulator |
| 中文描述： | 300mA的，低噪聲，超高速的CMOS LDO穩壓器 |
| 文件頁數： | 9/15頁 |
| 文件大?。?/td> | 261K |
| 代理商： | RT9198A-16PU5R |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁當前第9頁第10頁第11頁第12頁第13頁第14頁第15頁
RT9198/A
9
DS9198/A-10 November 2006
www.richtek.com
Applications Information
Like any low-dropout regulator, the external capacitors used
for the RT9198/A must be carefully selected for regulator
stability and performance. Using a capacitor whose value
is > 1
μ
F on the RT9198/A input and the amount of
capacitance can be increased without limit. The input
capacitor must be located a distance of not more than
0.5 inch from the input pin of the IC and returned to a
clean analog ground. Any good quality ceramic or tantalum
can be used for this capacitor. The capacitor with larger
value and lower ESR (equivalent series resistance) provides
better PSRR and line-transient response.
The output capacitor must meet both requirements for
minimum amount of capacitance and ESR in all LDOs
application. The RT9198/A is designed specifically to work
with low ESR ceramic output capacitor in space-saving
and performance consideration. Using a ceramic capacitor
whose value is at least 1
μ
F with ESR is more than 20m
Ω
on the RT9198/A output ensures stability. The RT9198/A
still works well with output capacitor of other types due to
the wide stable ESR range. Figure 1. shows the curves of
allowable ESR range as a function of load current for various
output capacitor values. Output capacitor of larger
capacitance can reduce noise and improve load transient
response, stability, and PSRR. The output capacitor should
be located with in 0.5 inch from the V
OUT
pin of the
RT9198/A and returned to a clean analog ground.
Thermal Considerations
Thermal protection limits power dissipation in RT9198/A.
When the operating junction temperature exceeds 165
°
C,
the OTP circuit starts the thermal shutdown function and
turns the pass element off. The pass element turns on
again after the junction temperature cools by 30
°
C.
For continuous operation, do not exceed absolute
maximum operatiog junction temperature 125
°
C. The
power dissipation definition in device is shown as following
formula :
P
D
= (V
IN
V
OUT
) x I
OUT
+ V
IN
x I
Q
The maximum power dissipation depends on the thermal
resistance of IC package, PCB layout, the rate of
surroundings airflow and temperature difference between
junction to ambient. The maximum power dissipation can
be calculated by following formula :
P
D(MAX)
= ( T
J(MAX)
- T
A
) /
θ
JA
Where T
J(MAX)
is the maximum operating junction
temperature 125
°
C, T
A
is the ambient temperature and the
θ
JA
is the junction to ambient thermal resistance.
Instable
Enable Function
The RT9198/A features an LDO regulator enable/disable
function.
To assure the RT9198 LDO regulator will switch on, the
EN turn on control level must be greater than 1.2V. The
RT9198 LDO regulator will go into shutdown mode when
the voltage on the EN pin falls below 0.4V. For RT9198A,
the EN turn on control level must be lower than 0.4V to
assure the RT9198A LDO regulator switch on. The
RT9198A LDO regulator will go into shutdown mode when
the voltage on the EN pin is higher than 1.2 V. The RT9198A
equips a quick-discharge function to protect the system.
When the regulator is turned off by EN pin, the internal
MOSFET between V
OUT
and GND will be turned on to
discharge output voltage quickly. If the enable function is
not needed in a specific application, it may be tied to
GND/VIN to keep the LDO regulator in a continuously on
state.
Figure 1
Region of Stable C
OUT
ESR vs. Load Current
100.00
0.00
0.01
0.10
1.00
10.00
0
50
100
150
200
250
300
Load Current (mA)
C
O
)
C
OUT
= 1uF
Instable
Stable
1
RT9198/A-15CU5
C
OUT
= 1
μ
F, X7R
Simulation Verify
相關PDF資料 |
PDF描述 |
|---|---|
| RT9198A-16PV | 300mA, Low Noise, Ultra-Fast CMOS LDO Regulator |
| RT9198A-16PY | 300mA, Low Noise, Ultra-Fast CMOS LDO Regulator |
| RT9198A-2HPU5R | 300mA, Low Noise, Ultra-Fast CMOS LDO Regulator |
| RT9198A-2HPV | 300mA, Low Noise, Ultra-Fast CMOS LDO Regulator |
| RT9198A-2HPY | 300mA, Low Noise, Ultra-Fast CMOS LDO Regulator |
相關代理商/技術參數 |
參數描述 |
|---|---|
| RT9199GS | 功能描述:IC REG BUS TERMINATION 2A 8SOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 專用型 系列:- 標準包裝:43 系列:- 應用:控制器，Intel VR11 輸入電壓:5 V ~ 12 V 輸出數:1 輸出電壓:0.5 V ~ 1.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-VFQFN 裸露焊盤 供應商設備封裝:48-QFN（7x7） 包裝:管件 |
| RT9199GSP | 功能描述:IC REG BUS TERMINATION 2A 8SOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 專用型 系列:- 標準包裝:2,000 系列:- 應用:控制器，DSP 輸入電壓:4.5 V ~ 25 V 輸出數:2 輸出電壓:最低可調至 1.2V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:30-TFSOP（0.173"，4.40mm 寬） 供應商設備封裝:30-TSSOP 包裝:帶卷 (TR) |
| RT9199PSP | 制造商:Richtek Technology Corporation 功能描述: |
| RT9201 | 制造商:RICHTEK 制造商全稱:Richtek Technology Corporation 功能描述:High Efficiency PWM Step-Down DC-DC Converter |
| RT9201GQV | 制造商:RICHTEK 制造商全稱:Richtek Technology Corporation 功能描述:High Efficiency PWM Step-Down DC-DC Converter |
發布緊急采購，3分鐘左右您將得到回復。