- 您現在的位置：買賣IC網 > PDF目錄385767 > RF2157 (RF MICRO DEVICES INC) PCS CDMA/TDMA 3V POWER AMPLIFIER PDF資料下載
參數資料
| 型號： | RF2157 |
| 廠商： | RF MICRO DEVICES INC |
| 元件分類： | 衰減器 |
| 英文描述： | PCS CDMA/TDMA 3V POWER AMPLIFIER |
| 中文描述： | 1750 MHz - 1780 MHz RF/MICROWAVE NARROW BAND MEDIUM POWER AMPLIFIER |
| 封裝： | 4 X 4 MM, LCC-16 |
| 文件頁數： | 4/10頁 |
| 文件大?。?/td> | 192K |
| 代理商： | RF2157 |
2-190
RF2157
Rev A19 010611
2
P
Pin
1
2
Function
GND
VPD1
Description
This pin is internally grounded to the die flag.
Interface Schematic
Power down control for first stage. When this pin is “l(fā)ow”, first stage cir-
cuits are shut off. When this pin is 2.8V, all first stage circuits are oper-
ating normally. V
PD1
requires a regulated 2.8V for the amplifier to
operate properly over all specified temperature and voltage ranges. A
dropping resistor from a higher regulated voltage may be used to pro-
vide the required 2.8V.
For full power operation, VMODE is set low. VMODE will reduce the
bias current by approximately 50% when set HIGH. Large Signal Gain
is reduced approximately 1.5dB at 29dBm P
OUT
. Small Signal Gain is
reduced by approximately 6dB at lower temperatures. An external
series resistor is optional to limit the amount of current required.
Power down control for the second stage. When this pin is “l(fā)ow”, the
second stage circuit is shut off. When this pin is 2.8V, the second stage
circuit is operating normally. V
PD
requires a regulated 2.8V for the
amplifier to operate properly over all specified temperature and voltage
ranges. A dropping resistor from a higher regulated voltage may be
used to provide the required 2.8V. A 15pF high frequency bypass
capacitor is recommended.
Connect to ground plane via 15nH inductor. DC return for the second
stage bias circuit.
This pin is internally a no connection. It is recommended that this pin
be connected to either the RF output matching network or to the
ground plane.
RF output and power supply for final stage. This is the unmatched col-
lector output of the second stage. A DC block is required following the
matching components. The biasing may be provided via a parallel L-C
set for resonance at the operating frequency of 1710MHz to 1910MHz.
It is important to select an inductor with very low DC resistance with a
1A current rating. Alternatively, shunt microstrip techniques are also
applicable and provide very low DC resistance. Low frequency bypass-
ing is required for stability.
Same as pin 7.
3
MODE
4
VPD2
5
GND
6
NC
7
RF OUT
8
9
10
RF OUT
GND
VCC
See pin 7.
This pin is internally grounded to the die flag.
Supply for bias reference and control circuits. High frequency bypass-
ing may be necessary.
Power supply for first stage and interstage match. Pins 11 and 12
should be connected by a common trace where the pins contact the
printed circuit board.
Same as pin 11.
11
VCC1
12
13
VCC1
NC
This pin is internally a no connection. It is recommended that this pin
be connected to either VCC1 or to the ground plane.
It is recommended that these pins be connected to the ground plane for
improved isolation between RF IN (pin 16) and the VCC1 pins (pins 11
and 12).
It is recommended that these pins be connected to the ground plane for
improved isolation between RF IN (pin 16) and the VCC1 pins (pins 11
and 12).
RF input. An external 15pF series capacitor is required as a DC block.
In addition, a series transmission line and shunt capacitor, 5pF, are
required to provide 2:1 VSWR.
14
NC
15
NC
16
RF IN
Pkg
Base
GND
Ground connection. The backside of the package should be soldered to
a top side ground pad which is connected to the ground plane with mul-
tiple vias. The pad should have a short thermal path to the ground
plane.
RF OUT
From Bias
Network
GND1
RF IN
VCC1
From
Bias
Stages
15 pF
5 pF
相關PDF資料 |
PDF描述 |
|---|---|
| RF2162 | 3V 900MHZ LINEAR AMPLIFIER |
| RF2162PCBA | 3V 900MHZ LINEAR AMPLIFIER |
| RF2163PCBA | CAP 33UF 350V ELECT EB SMD |
| RF2163 | 3V, 2.5GHZ LINEAR POWER AMPLIFIER |
| RF2172PCBA-H | ISM BAND 3.6V, 250MW AMP WITH ANALOG GAIN CONTROL |
相關代理商/技術參數 |
參數描述 |
|---|---|
| RF2157-000 | 功能描述:可復位保險絲 RoHS:否 制造商:Bourns 電流額定值: 電阻:7.5 Ohms 最大直流電壓: 保持電流:0.1 A 安裝風格:SMD/SMT 端接類型:SMD/SMT 跳閘電流:0.6 A 引線間隔: 系列:MF-PSHT 工作溫度范圍:- 40 C to + 125 C |
| RF2157PCBA | 制造商:RFMD 制造商全稱:RF Micro Devices 功能描述:PCS CDMA/TDMA 3V POWER AMPLIFIER |
| RF2157TR13 | 制造商:RF Micro Devices Inc 功能描述: 制造商:RFMD 功能描述: |
| RF2158-000 | 功能描述:可復位保險絲 RoHS:否 制造商:Bourns 電流額定值: 電阻:7.5 Ohms 最大直流電壓: 保持電流:0.1 A 安裝風格:SMD/SMT 端接類型:SMD/SMT 跳閘電流:0.6 A 引線間隔: 系列:MF-PSHT 工作溫度范圍:- 40 C to + 125 C |
| RF2159-000 | 功能描述:可復位保險絲 RoHS:否 制造商:Bourns 電流額定值: 電阻:7.5 Ohms 最大直流電壓: 保持電流:0.1 A 安裝風格:SMD/SMT 端接類型:SMD/SMT 跳閘電流:0.6 A 引線間隔: 系列:MF-PSHT 工作溫度范圍:- 40 C to + 125 C |
發布緊急采購，3分鐘左右您將得到回復。