
2-156
RF2152
Rev A8 001109
2
P
NOT FOR NEWDESIGNS
Total Current (Power down)
V
PD
“Low” Voltage
0
V
PD
“High” Voltage
2.7
2.8
MODE “High” Voltage
2.1
2.8
MODE “Low” Voltage
0
SeeUpgradedProductsRF 2162/F2192
2.9
2.9
0.5
Absolute Maximum Ratings
Parameter
Supply Voltage (RF off)
Supply Voltage (P
OUT
≤
31dBm)
DC Supply Current
Mode Voltage (V
MODE
)
Control Voltage (V
PD
)
Input RF Power
Operating Ambient Temperature
Storage Temperature
Moisture Sensitivity
Rating
+8.0
+5.2
1.0
+3.0
+3.0
+12
-40 to +85
-40 to +150
JEDEC LEVEL 5
Unit
V
DC
V
DC
A
V
DC
V
DC
dBm
°C
°C
Parameter
Specification
Typ.
Unit
Condition
Min.
Max.
Overall
T=25°C, V
CC
=3.4V, V
PD
=2.8V,
Freq=824MHz to 849MHz, unless otherwise
specified
Usable Frequency Range
Typical Frequency Range
800
960
MHz
MHz
MHz
dB
dBc
824-849
877-925
30
-38
Linear Gain
Second Harmonic (including
second harmonic trap)
Max CW Output Power
Total Efficiency (AMPS mode)
Maximum Linear Output Power
(CDMA Modulation)
Total Linear Efficiency
Adjacent Channel Power Rejec-
tion
Adjacent Channel Power Rejec-
tion
Input VSWR
Output Load VSWR
Noise Figure
Noise Power P
OUT
=15dBm
P
OUT
=28dBm
P
OUT
=31dBm
Power Supply
Power Supply Voltage
Idle current
28
-32
33
-42
Pout=28dBm
31
40
28
31.5
45
28.5
32
55
29
dBm
%
dBm
Tuned for CDMA
Tuned for CDMA
30
-44
35
-46
38
-50
%
dBc
ACPR@885kHz
-56
-58
-62
dBc
ACPR@1980kHz
< 2:1
10:1
6.1
No oscillations
V
CC
=3.4V
V
CC
=3.4V; 30KHz BW; RX Band NP mea-
sured from TX center band to RX center
band
5.9
6.0
86.5
89.3
92.3
dB
dBm
dBm
dBm
3.0
3.4
90
5.2
V
mA
MODE = low Pin 16=Ground AMPS/Low
Power CDMA Modes
MODE = high Pin 16=2.8V High Power
CDMA Mode (Pout>20dBm)
Pins7,8, Vpd=2.8V (Pin 7 typ. not connected,
I=5mA for Pin 8)
Idle current
200
mA
V
PD
current
10
mA
Turn On/Off time
<100
10
0.2
ns
μ
A
V
V
V
PD
= low
Caution!
ESD sensitive device.
RF Micro Devices believes the furnished information is correct and accurate
at the time of this printing. However, RF Micro Devices reserves the right to
make changes to its products without notice. RF Micro Devices does not
assume responsibility for the use of the described product(s).
Refer to “Handling of PSOP and PSSOP Products”
on page 16-15 for special handling information.