- 您現在的位置：買賣IC網 > PDF目錄374575 > RD28F3204W30B85 (INTEL CORP) 1.8 Volt Intel Wireless Flash Memory with 3 Volt I/O and SRAM (W30) PDF資料下載
參數資料
| 型號： | RD28F3204W30B85 |
| 廠商： | INTEL CORP |
| 元件分類： | 存儲器 |
| 英文描述： | 1.8 Volt Intel Wireless Flash Memory with 3 Volt I/O and SRAM (W30) |
| 中文描述： | SPECIALTY MEMORY CIRCUIT, PBGA80 |
| 封裝： | 14 X 8 MM, 0.80 MM PITCH, STACK, CSP-80 |
| 文件頁數： | 18/82頁 |
| 文件大小： | 749K |
| 代理商： | RD28F3204W30B85 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁當前第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁
28F6408W30, 28F3204W30, 28F320W30, 28F640W30
12
Preliminary
Wireless Flash Memory Flash Memory family
’
s LPA is at 0080h.
PA = User programmable 4-word protection address in the device identification plane.
PnA = Address within the partition.
XnA = Base Address where X can be partition, main block or parameter block. See
Figure 11,
“
Device
Identification Codes
”
on page 21
for details.
QA = Query code address.
WA = Word address of memory location to be written.
2. SRD = Data read from the status register on DQ
7-0.
WD = Data to be written at location WA.
IC = Identifier code data.
PD =User programmable 4-word protection data.
QD = Query code data on DQ
.
CD = Configuration register code data presented on device addresses A
. A
address bits can select
any partition
.
See
Table 6,
“
Configuration Register Bits
”
on page 13
for configuration register bits
descriptions.
3. Commands other than those shown above are reserved by Intel for future device implementations and
should not be used.
.
4.0
Flash Read Modes
4.1
Read Array
4.1.1
Asynchronous Mode
The 1.8 Volt Intel
Wireless Flash Memory with 3 Volt I/O supports asynchronous reads. An
asynchronous read is executed by implementing a read operation without the use of the CLK
signal. During an asynchronous read operation, the CLK signal is ignored. If asynchronous reads
will be the only read mode of operation, it is recommended that the CLK signal be held at a valid
V
IH
level.
Page mode is the default read mode after power-up or reset. A page-mode read outputs 4 words of
asynchronous data; however, by manipulating certain control signals, the device can be made to
output less than 4 words.
After power-up or reset, it is not necessary to execute the Read Array command before accessing
the flash memory. However, to perform a flash read at any other time, it is necessary to execute the
Read Array command before accessing the flash memory.
Page mode is permitted in all blocks, across all partition boundaries and operates independent of
V
PP
. A single-word read can be used to access register information. During asynchronous reads, the
address is latched on the rising edge of ADV#.
Upon completion of reading the array, the device automatically enters an Automatic Power Savings
(APS) mode. APS mode consumes power comparable to standby mode.
4.1.2
Synchronous Mode
The 1.8 Volt Intel
Wireless Flash Memory supports synchronous reads. A synchronous read is
executed by implementing a read operation with the use of the CLK signal. During a synchronous
read operation, the CLK signal edge (rising or falling) controls flash array access.
A burst-mode read is synchronized to the CLK signal and outputs a 4-, 8- or continuous-word data
stream based on configuration register settings. However, by manipulating certain control signals,
the device can be made to output less then 4-, 8- or continuous-words.
相關PDF資料 |
PDF描述 |
|---|---|
| RD28F3204W30T70 | 1.8 Volt Intel Wireless Flash Memory with 3 Volt I/O and SRAM (W30) |
| RD28F3204W30T85 | 1.8 Volt Intel Wireless Flash Memory with 3 Volt I/O and SRAM (W30) |
| RD28F6408W30B70 | 1.8 Volt Intel Wireless Flash Memory with 3 Volt I/O and SRAM (W30) |
| RD28F6408W30B85 | 1.8 Volt Intel Wireless Flash Memory with 3 Volt I/O and SRAM (W30) |
| RD28F6408W30T70 | 1.8 Volt Intel Wireless Flash Memory with 3 Volt I/O and SRAM (W30) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| RD28F3204W30T70 | 制造商:INTEL 制造商全稱:Intel Corporation 功能描述:1.8 Volt Intel Wireless Flash Memory with 3 Volt I/O and SRAM (W30) |
| RD28F3204W30T85 | 制造商:INTEL 制造商全稱:Intel Corporation 功能描述:1.8 Volt Intel Wireless Flash Memory with 3 Volt I/O and SRAM (W30) |
| RD28F3208C3B70 | 制造商:INTEL 制造商全稱:Intel Corporation 功能描述:3 VOLT INTEL Advanced+ Boot Block Flash Memory (C3) Stacked-Chip ScalPackage Familye |
| RD28F3208C3B90 | 制造商:INTEL 制造商全稱:Intel Corporation 功能描述:3 VOLT INTEL Advanced+ Boot Block Flash Memory (C3) Stacked-Chip ScalPackage Familye |
| RD28F3208C3T70 | 制造商:INTEL 制造商全稱:Intel Corporation 功能描述:3 VOLT INTEL Advanced+ Boot Block Flash Memory (C3) Stacked-Chip ScalPackage Familye |
發布緊急采購，3分鐘左右您將得到回復。