參數資料
型號： PXAG49KBA
廠商： NXP SEMICONDUCTORS
元件分類： 微控制器/微處理器
英文描述： XA 16-bit microcontroller family 64K FLASH/2K RAM, watchdog, 2 UARTs
中文描述： 16-BIT, FLASH, 30 MHz, MICROCONTROLLER, PQCC44
封裝： PLASTIC, LCC-44
文件頁數： 11/42頁
文件大?。?/td> 299K
代理商： PXAG49KBA
Philips Semiconductors
Preliminary specification
XA-G49
XA 16-bit microcontroller family
64K Flash/2K RAM, watchdog, 2 UARTs
2000 Apr 03
11
FFFF
C000
8000
4000
2000
0000
BLOCK 4
16k BYTES
BLOCK 3
16k BYTES
BLOCK 2
16k BYTES
BLOCK 1
8k BYTES
BLOCK 0
8k BYTES
PROGRAM
ADDRESS
BOOT ROM
FFFF
F800
SU01034
Figure 3. Flash Memory Configuration
FMIDLE
The FMIDLE bit in the AUXR register allows saving additional power
by turning off the Flash memory when the CPU is in the Idle mode.
This must be done just prior to initiating the Idle mode, as shown
below.
OR
AUXR,#$40
; Set Flash memory
to idle mode.
; Turn on Idle mode.
; Execution resumes
here when Idle
mode terminates.
OR
.
PCON,#$01
.
When the Flash memory is put into the Idle mode by setting FMIDLE,
restarting the CPU upon exiting Idle mode takes slightly longer,
about 3 microseconds. However, the standby current consumed by
the Flash memory is reduced from about 8mA to about 1mA.
Default Loader
A default loader that accepts programming commands in a
predetermined format is contained permanently in the Boot ROM. A
factory fresh device will enter this loader automatically if it is
powered up without first being programmed by the user. Loader
commands include functions such as erase block; program Flash
memory; read Flash memory; and blank check.
Boot Vector
The XA-G49 contains two special FLASH registers: the BOOT
VECTOR and the STATUS BYTE.
The “Boot Vector” allows forcing the execution of a user supplied
Flash loader upon reset, under two specific sets of conditions. At the
falling edge of reset, the XA-G49 examines the contents of the
Status Byte. If the Status Byte is set to zero, power-up execution
starts at location 0000H, which is the normal start address of the
user’s application code.
When the Status Byte is set to a value other than zero, the Boot
Vector is used as the reset vector (4 bytes), including the Boot
Program Counter (BPC) and the Boot PSW (BPSW). The factory
default settings are 8000h for the BPSW and F800h for the BPC,
which corresponds to the address F900h for the factory masked-ROM
ISP boot loader. The Status Byte is automatically set to a non-zero
value when a programming error occurs. A custom boot loader can
be written with the Boot Vector set to the custom boot loader.
NOTE:
bytes are erased at the same time. It is necessary to reprogram
the Boot Vector after erasing and updating the Status Byte.
When erasing the Status Byte or Boot Vector, these
Hardware Activation of the Boot Vector
Program execution at the Boot Vector may also be forced from
outside of the microcontroller by setting the correct state on a few
pins. While Reset is asserted, the PSEN pin must be pulled low, the
ALE pin allowed to float high (need not be pulled up externally), and
the EA pin driven to a logic high (or up to V
PP
). Then reset may be
released. This is the same effect as having a non-zero status byte.
This allows building an application that will normally execute the end
user’s code but can be manually forced into ISP operation. The Boot
ROM is enabled when use of the Boot Vector is forced as described
above, so the branch may go to the default loader. Conversely, user
code in the top 2k bytes of the Flash memory may not be executed
when the Boot Vector is used.
If the factory default setting for the BPC (F800h) is changed, it will no
longer point to the ISP masked-ROM boot loader code. If this happens,
the only possible way to change the contents of the Boot Vector is
through the parallel programming method, provided that the end user
application does not contain a customized loader that provides for
erasing and reprogramming of the Boot Vector and Status Byte.
After programming the FLASH, the status byte should be erased to
zero in order to allow execution of the user’s application code
beginning at address 0000H.
相關PDF資料
PDF描述
PXAG49KFA XA 16-bit microcontroller family 64K FLASH/2K RAM, watchdog, 2 UARTs
PXT2222 NPN switching transistor
PXT2907 PNP switching transistor
PXT3904 NPN switching transistor
PXT3906 PNP switching transistor
相關代理商/技術參數
參數描述
PXAG49KBA/00,512 功能描述:16位微控制器 - MCU 64K/2K FLISP 30M/LCC44 COM RoHS:否 制造商:Texas Instruments 核心:RISC 處理器系列:MSP430FR572x 數據總線寬度:16 bit 最大時鐘頻率:24 MHz 程序存儲器大小:8 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:VQFN-40 安裝風格:SMD/SMT
PXAG49KBBD 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:XA 16-bit microcontroller family
PXAG49KBBD/00,557 功能描述:16位微控制器 - MCU 64K/2K FL 16 BIT ISP/IAP COM RoHS:否 制造商:Texas Instruments 核心:RISC 處理器系列:MSP430FR572x 數據總線寬度:16 bit 最大時鐘頻率:24 MHz 程序存儲器大小:8 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:VQFN-40 安裝風格:SMD/SMT
PXAG49KFA 功能描述:16位微控制器 - MCU XA 16BIT 64KF/2KR IN SYS PROG -40+85 RoHS:否 制造商:Texas Instruments 核心:RISC 處理器系列:MSP430FR572x 數據總線寬度:16 bit 最大時鐘頻率:24 MHz 程序存儲器大小:8 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:VQFN-40 安裝風格:SMD/SMT
PXAG49KFA/00,512 功能描述:16位微控制器 - MCU 64K/2K FLISP 30M/LCC44 EXT RoHS:否 制造商:Texas Instruments 核心:RISC 處理器系列:MSP430FR572x 數據總線寬度:16 bit 最大時鐘頻率:24 MHz 程序存儲器大小:8 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:VQFN-40 安裝風格:SMD/SMT
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*