<var id="o9iyx"><label id="o9iyx"></label></var>
<menuitem id="o9iyx"><label id="o9iyx"></label></menuitem>
<dfn id="o9iyx"><tbody id="o9iyx"><optgroup id="o9iyx"></optgroup></tbody></dfn>
  • <li id="o9iyx"></li>
    <thead id="o9iyx"><meter id="o9iyx"><fieldset id="o9iyx"></fieldset></meter></thead><samp id="o9iyx"><dl id="o9iyx"><strike id="o9iyx"></strike></dl></samp>
    參數資料
    型號: PT4314C
    廠商: TEXAS INSTRUMENTS INC
    元件分類: 電源模塊
    英文描述: 2-OUTPUT 6 W DC-DC REG PWR SUPPLY MODULE
    封裝: SMD-9
    文件頁數: 9/10頁
    文件大?。?/td> 226K
    代理商: PT4314C
    Application Notes
    For technical support or further information,visit http://power.ti.com
    PT4310 Series
    Using the Remote On/Off Function on the
    PT4310 Isolated Dual Output DC/DC Converters
    For applications requiring output voltage On/Off control,
    the PT4310 DC/DC converter series incorporates a
    “Remote On/Off” control (pin 11). This feature can be used
    when there is a requirement for the module to be switched
    off without removing the applied input source voltage.
    The converter operates normally with Pin 11 open-circuit,
    and produces a regulated output voltage when a valid
    source voltage is applied to +Vin (pin 18), with respect
    to –Vin (pin 17). When a low-level 1 ground signal is
    applied to pin 11, the converter output will be turned off.
    Figure 2-1 shows an application schematic, which details
    the typical use of the Remote On/Off function. Note the
    discrete transistor (Q1). The control pin has its own
    internal pull-up, and must be controlled with an open-
    collector or open-drain device (See notes 2 & 3). Table 2-1
    gives the input requirements.
    When placed in the “Off” state, the standby current drawn
    from the input source is typically reduced to less than 1 mA.
    Table 2-1; Remote On/Off Control Requirements 1
    Parameter
    Min
    Typ
    Max
    Disable
    –0.1 V
    1 V
    Enable
    5 V 3
    Open-Circuit 2
    Vo/c [Open-Circuit]
    10 V
    Iin [pin 11 at –Vin]
    –200 A
    Notes:
    1. The Remote On/Off control uses –Vin (pin 17) as its
    ground reference. All voltages specified are with respect
    to –Vin.
    2. Use an open-collector device (preferably a discrete
    transistor) for the Remote On/Off input. Do not connect
    a pull-up resistor directly to pin 11.
    3. The Remote On/Off pin may be controlled with devices that
    have a totem-pole output providing that a blocking
    diode is used. The blocking diode is required to prevent
    current from being injected into On/Off control pin.
    Note: For TTL devices a pull-up may be required on the
    cathode side of the blocking diode. This is to guarantee a
    minimum enable voltage at pin 11 (See Figure 2-1).
    4. The PT4310 converters incorporate an “Under-Voltage
    Lockout” (UVLO). The UVLO will keep the module
    off when the input voltage to the converter is low,
    regardless of the state of the Remote On/Off control.
    Table 2-2 gives the UVLO input voltage thresholds.
    Figure 2-1
    Turn-On Time:
    In the circuit of Figure 2-1, turning Q1 on
    applies a low-voltage to pin 11 and disables the converter
    output. Correspondingly, turning Q1 off allows the con-
    verter to power up and produce a regulated output voltage
    within 50 ms. Although the rise-time of the output is short
    (<1ms), the delay time will vary depending upon the input
    voltage and the module’s internal timing. Figure 2-2
    shows response of the +5-V output from the PT4311
    (±5 V), following the turn-off of Q1 at time t =0. The
    waveform was measured with a 48 Vdc input voltage,
    and 0.25-Adc resistive load at both the positive and
    negative outputs.
    Figure 2-2
    R1
    10k
    Q1
    BSS138
    +V
    o
    -V
    o
    +V
    in
    -V
    in
    Vdd
    1 =OFF
    Note 1
    U1a
    Note 1
    D1
    1N4148 #
    # or similar low-leakage PIN diode
    PT4310
    +Vin
    -Vin
    ±Vo
    Adjust
    11
    17
    18
    1
    2
    3
    COM
    Remote
    On/Off
    12
    Vo
    1 ( + )
    Vo
    2 ( – )
    0
    5
    10
    15
    20
    25
    30
    time (milli-secs)
    VO (2V/Div)
    delay time
    Table 2-2; UVLO Thresholds 4
    Series
    Vin Range
    UVLO Threshold
    PT4310
    38 – 75 V
    36 ±2 V
    相關PDF資料
    PDF描述
    PT4311A 2-OUTPUT 6 W DC-DC REG PWR SUPPLY MODULE
    PT4311C 2-OUTPUT 6 W DC-DC REG PWR SUPPLY MODULE
    PT4313A 2-OUTPUT 6 W DC-DC REG PWR SUPPLY MODULE
    PT4313C 2-OUTPUT 6 W DC-DC REG PWR SUPPLY MODULE
    PT4471C 1-OUTPUT 100 W DC-DC REG PWR SUPPLY MODULE
    相關代理商/技術參數
    參數描述
    PT4316 制造商:PTC 制造商全稱:Princeton Technology Corp 功能描述:Low Power 315/433 MHz OOK/ASK Superheterodyne Receiver with SAW-based Oscillator
    PT4316-S 制造商:PTC 制造商全稱:Princeton Technology Corp 功能描述:Low Power 315/433 MHz OOK/ASK Superheterodyne Receiver with SAW-based Oscillator
    PT4316-SL 制造商:PTC 制造商全稱:Princeton Technology Corp 功能描述:Low Power 315/433 MHz OOK/ASK Superheterodyne Receiver with SAW-based Oscillator
    PT4316-X 制造商:PTC 制造商全稱:Princeton Technology Corp 功能描述:Low Power 315/433 MHz OOK/ASK Superheterodyne Receiver with SAW-based Oscillator
    PT4316-XL 制造商:PTC 制造商全稱:Princeton Technology Corp 功能描述:Low Power 315/433 MHz OOK/ASK Superheterodyne Receiver with SAW-based Oscillator