參數資料
型號： PR23MF11NIPF
廠商： Sharp Corporation
英文描述： Non-Zero Cross type DIP 8pin Triac output SSR
中文描述： 非零交叉式雙酯雙向晶閘管輸出蘇維埃社會主義共和國，8引腳
文件頁數： 9/15頁
文件大小： 282K
代理商： PR23MF11NIPF
9
PR23MF11NSZ Series
PR33MF11NSZ Series
■
Design Considerations
●
Recommended Operating Conditions
Parameter
Input signal current at ON state
Input signal current at OFF state
In order for the SSR to turn off, the triggering current (I
F
) must be 0.1mA or less.
In phase control applications or where the SSR is being by a pulse signal, please ensure that the pulse width
is a minimum of 1ms.
When the input current (I
F
) is below 0.1mA, the output Triac will be in the open circuit mode. However, if the
voltage across the Triac, V
D
, increases faster than rated dV/dt, the Triac may turn on. To avoid this situation,
please incorporate a snubber circuit. Due to the many different types of load that can be driven, we can
merely recommend some circuit values to start with : Cs
=
0.022
μ
F and Rs
=
47
. The operation of the SSR
and snubber circuit should be tested and if unintentional switching occurs, please adjust the snubber circuit
component values accordingly.
When making the transition from On to Off state, a snubber circuit should be used ensure that sudden drops
in current are not accompanied by large instantaneous changes in voltage across the Triac.
This fast change in voltage is brought about by the phase difference between current and voltage.
Primarily, this is experienced in driving loads which are inductive such as motors and solenods.
Following the procedure outlined above should provide sufficient results.
Any snubber or Varistor used for the above mentioned scenarios should be located as close to the main
output triac as possible.
All pins shall be used by soldering on the board. (Socket and others shall not be used.)
●
Degradation
In general, the emission of the IRED used in SSR will degrade over time.
In the case where long term operation and / or constant extreme temperature fluctuations will be applied to
the devices, please allow for a worst case scenario of 50% degradation over 5years.
Therefore in order to maintain proper operation, a design implementing these SSRs should provide at least
twice the minimum required triggering current from initial operation.
●
Design guide
Sheet No.: D4-A00301EN
PR23MF11NSZ
PR33MF11NSZ
Symbol
I
F
(ON)
I
F
(OFF)
Unit
mA
mA
Input
Output
Load supply voltage
Load supply current
Frequency
Operating temperature
V
OUT
(rms)
I
OUT
(rms)
f
T
opr
V
mA
Hz
C
Locate snubber circuit between output terminals
(Cs
=
0.022
μ
F, Rs
=
47
)
Conditions
20
0
50
20
25
0.1
120
240
I
T
(rms)
×
80%(
)
60
80
MIN.
MAX.
(
) See Fig.2 about derating curve (I
T
(rms) vs. ambient temperature).
相關PDF資料
PDF描述
PR23MF11NSZF Non-Zero Cross type DIP 8pin Triac output SSR
PR33MF11NIPF Non-Zero Cross type DIP 8pin Triac output SSR
PR33MF11NSZF Non-Zero Cross type DIP 8pin Triac output SSR
PR33MF11YIPF Non-Zero Cross type DIP 8pin Triac output SSR
PR33MF11YSZF Non-Zero Cross type DIP 8pin Triac output SSR
相關代理商/技術參數
參數描述
PR23MF11NSZ 制造商:SHARP 制造商全稱:Sharp Electrionic Components 功能描述:Non-Zero Cross type DIP 8pin Triac output SSR
PR23MF11NSZF 功能描述:固態繼電器-PCB安裝 8-DIP NON-ZC 10mA RoHS:否 制造商:Omron Electronics 控制電壓范圍: 負載電壓額定值:40 V 負載電流額定值:120 mA 觸點形式:1 Form A (SPST-NO) 輸出設備:MOSFET 封裝 / 箱體:USOP-4 安裝風格:SMD/SMT
PR-23SY / 1BAR / 81549.33 / 0-5V 制造商:KELLER 功能描述:TRANSMITTER PRESSURE 1BAR 制造商:KELLER 功能描述:TRANSMITTER, PRESSURE, 1BAR
PR-23SY / 1BAR / 81549.33 / 4-20MA 制造商:KELLER 功能描述:TRANSMITTER PRESSURE 1BAR 制造商:KELLER 功能描述:TRANSMITTER, PRESSURE, 1BAR
PR24 制造商:Hubbell Wiring Device-Kellems 功能描述:POWSTRP,66VRT,30-24A/250V,IEC-R,NM-P,24
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*