參數資料
型號: PIC24FJ32GA004-E/ML
廠商: Microchip Technology
文件頁數: 14/52頁
文件大?。?/td> 0K
描述: IC PIC MCU FLASH 32K 44-QFN
特色產品: PIC24FJ/33FJ MCUs & dsPIC? DSCs
標準包裝: 45
系列: PIC® 24F
核心處理器: PIC
芯體尺寸: 16-位
速度: 32MHz
連通性: I²C,PMP,SPI,UART/USART
外圍設備: 欠壓檢測/復位,LVD,POR,PWM,WDT
輸入/輸出數: 35
程序存儲器容量: 32KB(11K x 24)
程序存儲器類型: 閃存
RAM 容量: 8K x 8
電壓 - 電源 (Vcc/Vdd): 2 V ~ 3.6 V
數據轉換器: A/D 13x10b
振蕩器型: 內部
工作溫度: -40°C ~ 125°C
封裝/外殼: 44-VQFN 裸露焊盤
包裝: 管件
產品目錄頁面: 647 (CN2011-ZH PDF)
配用: 876-1004-ND - PIC24 BREAKOUT BOARD
DM240011-ND - KIT STARTER MPLAB FOR PIC24F MCU
AC162088-ND - HEADER MPLAB ICD2 24FJ64GA004 28
AC164336-ND - MODULE SOCKET FOR PM3 28/44QFN
DV164033-ND - KIT START EXPLORER 16 MPLAB ICD2
2008 Microchip Technology Inc.
DS39768D-page 21
PIC24FJXXXGA0XX
3.7
Writing Configuration Words
The PIC24FJXXXGA0XX family configuration is stored
in Flash Configuration Words at the end of the user
space program memory and in multiple register
Configuration Words located in the test space.
These registers reflect values read at any Reset from
program memory locations. The values can be changed
only by programming the content of the corresponding
Flash Configuration Word and resetting the device. The
Reset forces an automatic reload of the Flash stored
configuration
values
by
sequencing
through
the
dedicated Flash Configuration Words and transferring
the data into the Configuration registers. To change the
values of the Flash Configuration Word once it has been
programmed, the device must be Chip Erased, as
and reprogrammed to the desired value. It is not
possible to program a ‘0’ to ‘1’, but they may be
programmed from a ‘1’ to ‘0’ to enable code protection.
Table 3-7 shows the ICSP programming details for pro-
gramming the Configuration Word locations, including
the serial pattern with the ICSP command code which
must be transmitted, Least Significant bit first, using the
PGCx and PGDx pins (see Figure 3-2).
In Step 1, the Reset vector is exited. In Step 2, the
NVMCON register is initialized for programming of
code memory. In Step 3, the 24-bit starting destination
address for programming is loaded into the TBLPAG
register and W7 register.
The TBLPAG register must be loaded with the
following:
96 and 64 Kbyte devices – 00h
128 Kbyte devices – 01h
To verify the data by reading the Configuration Words
after performing the write in order, the code protection
bits initially should be programmed to a ‘1’ to ensure
that the verification can be performed properly. After
verification is finished, the code protection bit can be
programmed to a ‘0’ by using a word write to the
appropriate Configuration Word.
TABLE 3-6:
DEFAULT CONFIGURATION
REGISTER VALUES
Address
Name
Default Value
Last Word
CW1
7FFFh(1)
Last Word – 2
CW2
FFFFh
Note 1:
CW1<15> is reserved and must be
programmed to ‘0’.
相關PDF資料
PDF描述
PIC32MX220F032D-I/TL IC MCU 32BIT 32KB FLASH 44-VTLA
DSPIC30F2011-30I/P IC DSPIC MCU/DSP 12K 18DIP
PIC16F914-I/ML IC PIC MCU FLASH 4KX14 44QFN
PIC18F26J50-I/SO IC PIC MCU FLASH 64K 2V 28-SOIC
PIC16F872-I/SO IC MCU FLASH 2KX14 EE 28SOIC
相關代理商/技術參數
參數描述
PIC24FJ32GA004-I/ML 功能描述:16位微控制器 - MCU 32KB FL 8192b RAM 16MIPS 35I/O 16b Fam RoHS:否 制造商:Texas Instruments 核心:RISC 處理器系列:MSP430FR572x 數據總線寬度:16 bit 最大時鐘頻率:24 MHz 程序存儲器大小:8 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:VQFN-40 安裝風格:SMD/SMT
PIC24FJ32GA004-I/ML 制造商:Microchip Technology Inc 功能描述:IC 16BIT MCU PIC24F 32MHZ QFN-44 制造商:Microchip Technology Inc 功能描述:IC, 16BIT MCU, PIC24F, 32MHZ, QFN-44
PIC24FJ32GA004-I/PT 功能描述:16位微控制器 - MCU 32KB 8192 bytes 16MIPS 35 I/O RoHS:否 制造商:Texas Instruments 核心:RISC 處理器系列:MSP430FR572x 數據總線寬度:16 bit 最大時鐘頻率:24 MHz 程序存儲器大小:8 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:2 V to 3.6 V 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:VQFN-40 安裝風格:SMD/SMT
PIC24FJ32GA004-I/PTC04 制造商:Microchip Technology Inc 功能描述:MCCPIC24FJ32GA004-I/PTC04 PIC24FJ32GA004
PIC24FJ32GA004T-E/PT 制造商:Microchip Technology Inc 功能描述: