- 您現在的位置：買賣IC網 > PDF目錄1963 > PIC16F526-I/MG (Microchip Technology)MCU PIC 1.5K FLASH 3X3 16QFN PDF資料下載
參數資料
| 型號： | PIC16F526-I/MG |
| 廠商： | Microchip Technology |
| 文件頁數： | 15/21頁 |
| 文件大小： | 0K |
| 描述： | MCU PIC 1.5K FLASH 3X3 16QFN |
| 產品培訓模塊： | 8-bit PIC® Microcontroller Portfolio |
| 標準包裝： | 120 |
| 系列： | PIC® 16F |
| 核心處理器： | PIC |
| 芯體尺寸： | 8-位 |
| 速度： | 20MHz |
| 外圍設備： | POR，WDT |
| 輸入/輸出數： | 11 |
| 程序存儲器容量： | 1.5KB（1K x 12） |
| 程序存儲器類型： | 閃存 |
| RAM 容量： | 67 x 8 |
| 電壓 - 電源 (Vcc/Vdd)： | 2 V ~ 5.5 V |
| 數據轉換器： | A/D 3x8b |
| 振蕩器型： | 內部 |
| 工作溫度： | -40°C ~ 85°C |
| 封裝/外殼： | 16-VFQFN 裸露焊盤 |
| 包裝： | 托盤 |
| 產品目錄頁面： | 638 (CN2011-ZH PDF) |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁當前第15頁第16頁第17頁第18頁第19頁第20頁第21頁
2007 Microchip Technology Inc.
DS41317B-page 3
PIC16F526
3.0
COMMANDS AND
ALGORITHMS
3.1
Program/Verify Mode
The Program/Verify mode is entered by holding pins
ICSPCLK and ICSPDAT low while raising VDD pin from
VIL to VDD. Then raise VPP from VIL to VIHH. Once in
this mode, the user program memory and configuration
memory can be accessed and programmed in serial
fashion. Clock and data are Schmitt Trigger input in this
mode.
The sequence that enters the device into the Program-
ming/Verify mode places all other logic into the Reset
state (the MCLR pin was initially at VIL). This means
that all I/Os are in the Reset state (high-impedance
inputs).
3.1.1
PROGRAMMING
The programming sequence loads a word, programs,
verifies and finally increments the PC.
Program/Verify mode entry will set the address to
0x7FF. The Increment Address command will
increment the PC. The available commands are shown
in Table 3-1.
FIGURE 3-1:
ENTERING HIGH
VOLTAGE PROGRAM/
VERIFY MODE
3.1.2
SERIAL PROGRAM/VERIFY
OPERATION
The RB1 pin is used as a clock input pin, and the RB0
pin is used for entering command bits and data input/
output during serial operation. To input a command, the
clock pin (RB1) is cycled 6 times. Each command bit is
latched on the falling edge of the clock with the Least
Significant bit (LSb) of the command being input first.
The data on pin RB0 is required to have a minimum
setup and hold time of 100 ns with respect to the falling
edge of the clock. Commands that have data associ-
ated with them (Read and Load) are specified to have
a minimum delay of 1 s between the command and
the data. After this delay the clock pin is cycled 16 times
with the first cycle being a Start bit and the last cycle
being a Stop bit. Data is also input and output LSb first,
with data input being latched on the falling edge of the
clock and data output being driven on the rising edge of
the clock. Therefore, during a Read operation the LSb
will be transmitted onto pin RB0 on the rising edge of
the second cycle, and during a Load operation the LSb
will be latched on the falling edge of the second cycle.
A minimum 1 s delay is also specified between con-
secutive commands; except the “End Programming”
command which requires a 100 s delay. Because this
is a 12-bit core, the two MSbs of the data word are
ignored. The commands that are available are
described in Table 3-1.
TABLE 3-1:
COMMAND MAPPING LOAD DATA
VPP
THLD0
VDD
TPPDP
RB1
(ICSPCLK)
(ICSPDAT)
RB0
Command
Mapping
(MSb ... LSb)
Hex
Value
Data
Load Data
X X 0 0 1 0
2
start_bit, data (14), stop_bit
Read Data
X X 0 1 0 0
4
start_bit, data (14), stop_bit
Increment Address
X X 0 1 1 0
6
Begin Programming
X X 1 0 0 0
8
End Programming
X X 1 1 1 0
E
Bulk Erase Program Memory
X X 1 0 0 1
9
相關PDF資料 |
PDF描述 |
|---|---|
| PIC16F526-I/SL | IC PIC MCU FLASH 1KX12 14SOIC |
| PIC16F59-I/PT | IC PIC MCU FLASH 2KX12 44TQFP |
| PIC16F616-I/P | IC PIC MCU FLASH 2KX14 14DIP |
| PIC16F628-20I/SS | IC MCU FLASH 2KX14 COMP 20SSOP |
| PIC16F639-I/SS | IC MCU FLASH 2KX14 20SSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PIC16F526T-I/MG | 功能描述:8位微控制器 -MCU 1.5KB 64B 8MHz Internal Oscillator RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| PIC16F526T-I/SL | 功能描述:8位微控制器 -MCU 15KB 64B 8MHz 8B ADC Internal Oscillator RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| PIC16F526T-I/SL030 | 制造商:Microchip Technology Inc 功能描述: |
| PIC16F526T-I/SL031 | 制造商:Microchip Technology Inc 功能描述: |
| PIC16F526T-I/SL033 | 制造商:Microchip Technology Inc 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。