- 您現在的位置：買賣IC網 > PDF目錄10900 > PIC16C55-RCE/SP (Microchip Technology)IC MCU OTP 512X12 28DIP PDF資料下載
參數資料
| 型號： | PIC16C55-RCE/SP |
| 廠商： | Microchip Technology |
| 文件頁數： | 41/194頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC MCU OTP 512X12 28DIP |
| 標準包裝： | 15 |
| 系列： | PIC® 16C |
| 核心處理器： | PIC |
| 芯體尺寸： | 8-位 |
| 速度： | 4MHz |
| 外圍設備： | POR，WDT |
| 輸入/輸出數： | 20 |
| 程序存儲器容量： | 768B（512 x 12） |
| 程序存儲器類型： | OTP |
| RAM 容量： | 24 x 8 |
| 電壓 - 電源 (Vcc/Vdd)： | 3.25 V ~ 6 V |
| 振蕩器型： | 外部 |
| 工作溫度： | -40°C ~ 125°C |
| 封裝/外殼： | 28-DIP（0.300"，7.62mm） |
| 包裝： | 管件 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁當前第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁第159頁第160頁第161頁第162頁第163頁第164頁第165頁第166頁第167頁第168頁第169頁第170頁第171頁第172頁第173頁第174頁第175頁第176頁第177頁第178頁第179頁第180頁第181頁第182頁第183頁第184頁第185頁第186頁第187頁第188頁第189頁第190頁第191頁第192頁第193頁第194頁
PIC18F2450/4450
2006 Microchip Technology Inc.
Advance Information
DS39760A-page 133
TABLE 14-1:
DIFFERENTIAL OUTPUTS TO
TRANSCEIVER
TABLE 14-2:
SINGLE-ENDED INPUTS
FROM TRANSCEIVER
The UOE signal toggles the state of the external
transceiver. This line is pulled low by the device to
enable the transmission of data from the SIE to an
external device.
14.2.2.3
Pull-up Resistors
The PIC18F2450/4450 devices require an external pull-
up resistor to meet the requirements for low-speed and
full-speed USB. Either an external 3.3V supply or the
VUSB pin may be used to pull up D+ or D-. The pull-up
resistor must be 1.5 k
Ω (±5%) as required by the USB
specifications. Figure 14-3 shows an example with the
VUSB pin.
FIGURE 14-3:
EXTERNAL CIRCUITRY
14.2.2.4
Ping-Pong Buffer Configuration
The usage of ping-pong buffers is configured using the
PPB1:PPB0 bits. Refer to Section 14.4.4 “Ping-Pong
Buffering” for a complete explanation of the ping-pong
buffers.
14.2.2.5
USB Output Enable Monitor
The USB OE monitor provides indication as to whether
the SIE is listening to the bus or actively driving the bus.
This is enabled by default when using an external
transceiver or when UCFG<6> = 1.
The USB OE monitoring is useful for initial system
debugging, as well as scope triggering during eye
pattern generation tests.
14.2.2.6
Eye Pattern Test Enable
An automatic eye pattern test can be generated by the
module when the UCFG<7> bit is set. The eye pattern
output will be observable based on module settings,
meaning that the user is first responsible for configuring
the SIE clock settings, pull-up resistor and Transceiver
mode. In addition, the module has to be enabled.
Once UTEYE is set, the module emulates a switch from
a receive to transmit state and will start transmitting a
J-K-J-K bit sequence (K-J-K-J for full speed). The
sequence will be repeated indefinitely while the Eye
Pattern Test mode is enabled.
Note that this bit should never be set while the module
is connected to an actual USB system. This test mode
is intended for board verification to aid with USB
certification tests. It is intended to show a system
developer the noise integrity of the USB signals which
can
be
affected
by
board
traces,
impedance
mismatches
and
proximity
to
other
system
components. It does not properly test the transition
from a receive to a transmit state. Although the eye
pattern is not meant to replace the more complex USB
certification test, it should aid during first order system
debugging.
14.2.2.7
Internal Regulator
The PIC18F2450/4450 devices have a built-in 3.3V
regulator to provide power to the internal transceiver and
provide a source for the external pull-ups. An external
220 nF (±20%) capacitor is required for stability.
The regulator is enabled by default and can be disabled
through the VREGEN Configuration bit. When enabled,
the voltage is visible on pin VUSB. When the regulator
is disabled, a 3.3V source must be provided through
the VUSB pin for the internal transceiver. If the internal
transceiver is disabled, VUSB is not used.
VPO
VMO
Bus State
00
Single-Ended Zero
01
Differential ‘0’
10
Differential ‘1’
11
Illegal Condition
VP
VM
Bus State
00
Single-Ended Zero
01
Low Speed
10
High Speed
11
Error
PIC
Microcontroller
Host
Controller/HUB
VUSB
D+
D-
Note:
The above setting shows a typical connection
for a full-speed configuration using an on-chip
regulator and an external pull-up resistor.
1.5 k
Ω
Note:
The drive from VUSB is sufficient to only
drive an external pull-up in addition to the
internal transceiver.
Note 1: Do not enable the internal regulator if an
external regulator is connected to VUSB.
2: VDD must be greater than VUSB at all
times, even with the regulator disabled.
相關PDF資料 |
PDF描述 |
|---|---|
| PIC16C55-RCE/SO | IC MCU OTP 512X12 28SOIC |
| PIC16C55-LPE/SS | IC MCU OTP 512X12 28SSOP |
| PIC16C55-LPE/SP | IC MCU OTP 512X12 28DIP |
| PIC16C55-LPE/SO | IC MCU OTP 512X12 28SOIC |
| PIC16C55-LPE/P | IC MCU OTP 512X12 28DIP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PIC16C55-RCI/P | 功能描述:8位微控制器 -MCU .75KB 24 RAM 20 I/O RC IndTemp PDIP28 RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| PIC16C55-RCI/SO | 功能描述:8位微控制器 -MCU .75KB 24 RAM 20 I/O RC IndTemp SOIC28 RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| PIC16C55-RCI/SP | 功能描述:8位微控制器 -MCU .75KB 24 RAM 20 I/O RC IndTemp SPDIP28 RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| PIC16C55-RCI/SS | 功能描述:8位微控制器 -MCU .75KB 24 RAM 20 I/O RC IndTemp SSOP28 RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| PIC16C55T-10/SO | 功能描述:8位微控制器 -MCU .75KB 24 RAM 20 I/O RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
發布緊急采購，3分鐘左右您將得到回復。