- 您現在的位置：買賣IC網 > PDF目錄1960 > PCF8575TS/1,112 (NXP Semiconductors)IC I/O EXPANDER I2C 16B 24SSOP PDF資料下載
參數資料
| 型號： | PCF8575TS/1,112 |
| 廠商： | NXP Semiconductors |
| 文件頁數： | 21/24頁 |
| 文件大小： | 0K |
| 描述： | IC I/O EXPANDER I2C 16B 24SSOP |
| 產品培訓模塊： | I²C Bus Fundamentals |
| 特色產品： | NXP - I2C Interface |
| 標準包裝： | 59 |
| 接口： | I²C |
| 輸入/輸出數： | 16 |
| 中斷輸出： | 是 |
| 頻率 - 時鐘： | 400kHz |
| 電源電壓： | 4.5 V ~ 5.5 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 24-SSOP（0.209"，5.30mm 寬） |
| 供應商設備封裝： | 24-SSOP |
| 包裝： | 管件 |
| 包括： | POR |
| 產品目錄頁面： | 827 (CN2011-ZH PDF) |
| 其它名稱： | 568-3989-5 935276552112 PCF8575TSDB PCF8575TSDB-ND |
1999 Apr 07
6
Philips Semiconductors
Product specication
Remote 16-bit I/O expander for I2C-bus
PCF8575
6
CHARACTERISTICS OF THE I2C-BUS
The I2C-bus is for bidirectional, 2-line communication
between different ICs or modules. The two lines are a
serial data line (SDA) and a serial clock line (SCL). Both
lines must be connected to a positive supply via a pull-up
resistor when connected to the output stages of a device.
Data transfer may be initiated only when the bus is not
busy.
6.1
Bit transfer
One data bit is transferred during each clock pulse.
The data on the SDA line must remain stable during the
HIGH period of the clock pulse as changes in the data line
at this time will be interpreted as control signals
(see Fig.3).
6.2
START and STOP conditions
Both data and clock lines remain HIGH when the bus is not
busy. A HIGH-to-LOW transition of the data line, while the
clock is HIGH is defined as the START condition (S).
A LOW-to-HIGH transition of the data line while the clock
is HIGH is defined as the STOP condition P (see Fig.4).
6.3
System conguration
A device generating a message is a ‘transmitter’, a device
receiving the message is the ‘receiver’. The device that
controls the message is the ‘master’ and the devices which
are controlled by the master are the ‘slaves’ (see Fig.5).
6.4
Acknowledge
The number of data bytes transferred between the START
and the STOP conditions from transmitter to receiver is not
limited. Each byte of eight bits is followed by one
acknowledge bit. The transmitter must release the SDA
line before the receiver can send an acknowledge bit.
A slave receiver which is addressed must generate an
acknowledge after the reception of each byte. Also a
master must generate an acknowledge after the reception
of each byte that has been clocked out of the slave
transmitter. The device that acknowledges has to pull
down the SDA line during the acknowledge clock pulse, so
that the SDA line is stable LOW during the HIGH period of
the acknowledge related clock pulse, set-up and hold
times must be taken into account.
A master receiver must signal an end of data to the
transmitter by not generating an acknowledge after the
last byte that has been clocked out of the slave. This is
done by the master receiver by holding the SDA line HIGH.
In this event the transmitter must release the data line to
enable the master to generate a STOP condition.
Fig.3 Bit transfer.
handbook, full pagewidth
MBC621
data line
stable;
data valid
change
of data
allowed
SDA
SCL
相關PDF資料 |
PDF描述 |
|---|---|
| PCI7620ZHK | IC 2SLT PC CARD/SC CTLR 288-PBGA |
| PCX7447AVGH1167NB | IC MPU 32BIT 1167MHZ 360CBGA |
| PEB1756E | IC MUX/DEMUX STS192/STM64 1397CB |
| PEB1757E | IC MUX/DEMUX STS192/STM64 1397CB |
| PI2DBS212ZHEX | IC MUX/DEMUX 2X1 28TQFN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PCF8575TSDB | 制造商:NXP Semiconductors 功能描述:I2C GPIO Expander 5.5V 24-Pin SSOP Tube |
| PCF8575TSDB-T | 制造商:NXP Semiconductors 功能描述: |
| PCF8576 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Universal LCD driver for low multiplex rates |
| PCF8576_01 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Universal LCD driver for low multiplex rates |
| PCF8576C | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Universal LCD driver for low multiplex rates |
發布緊急采購，3分鐘左右您將得到回復。