- 您現在的位置：買賣IC網 > PDF目錄385706 > PCF8574P (NXP Semiconductors N.V.) Remote 8-bit I-O expander for I2C-bus PDF資料下載
參數資料
| 型號： | PCF8574P |
| 廠商： | NXP Semiconductors N.V. |
| 元件分類： | I2C/I2S |
| 英文描述： | Remote 8-bit I-O expander for I2C-bus |
| 封裝： | PCF8574AP<SOT38-4 (DIP16)|<<http://www.nxp.com/packages/SOT38-4.html<1<Always Pb-free,;PCF8574AT/3<SOT162-1 (SO16)|<<http://www.nxp.com/packages/SOT162-1.html<1<wee |
| 文件頁數： | 12/24頁 |
| 文件大?。?/td> | 132K |
| 代理商： | PCF8574P |
2002 Nov 22
12
Philips Semiconductors
Product specification
Remote 8-bit I/O expander for I
2
C-bus
PCF8574
7.2
Interrupt output
The PCF8574 provides an open-drain output (INT) which
can be fed to a corresponding input of the microcontroller
(see Figs 13 and 14). This gives these chips a type of
master function which can initiate an action elsewhere in
the system.
Aninterruptisgeneratedbyanyrisingorfallingedgeofthe
port inputs in the input mode. After time t
iv
the signal INT is
valid.
Resetting and reactivating the interrupt circuit is achieved
when data on the port is changed to the original setting or
dataisreadfromorwrittentotheportwhichhasgenerated
the interrupt.
Resetting occurs as follows:
IntheREADmodeattheacknowledgebitaftertherising
edge of the SCL signal
In the WRITE mode at the acknowledge bit after the
HIGH-to-LOW transition of the SCL signal
Interrupts which occur during the acknowledge clock
pulse may be lost (or very short) due to the resetting of
the interrupt during this pulse.
Each change of the I/Os after resetting will be detected
and, after the next rising clock edge, will be transmitted as
INT. Reading from or writing to another device does not
affect the interrupt circuit.
7.3
Quasi-bidirectional I/Os
A quasi-bidirectional I/O can be used as an input or output
without the use of a control signal for data direction
(see Fig.15). At power-on the I/Os are HIGH. In this mode
only a current source to V
DD
is active. An additional strong
pull-up to V
DD
allows fast rising edges into heavily loaded
outputs. These devices turn on when an output is written
HIGH, and are switched off by the negative edge of SCL.
The I/Os should be HIGH before being used as inputs.
handbook, full pagewidth
MBD976
MICROCONTROLLER
INT
INT
INT
PCF8574
(1)
PCF8574
(2)
VDD
INT
PCF8574
(16)
Fig.13 Application of multiple PCF8574s with interrupt.
Fig.14 Interrupt generated by a change of input to I/O P5.
handbook, full pagewidth
MBD972
S
0
1
0
0
A2
A1
A0
1
A
start condition
1
P5
R/W
acknowledge
from slave
1
SDA
SCL
DATA INTO
P5
tir
INT
slave address (PCF8574)
data from port
1
2
3
4
5
6
7
8
P
stop
condition
tiv
相關PDF資料 |
PDF描述 |
|---|---|
| PCF8574T | Remote 8-bit I-O expander for I2C-bus |
| PCH1632 | CHIP TYPE IMPEDANCE CONVERTER |
| PCH163250B | CHIP TYPE IMPEDANCE CONVERTER |
| PCH163250T | CHIP TYPE IMPEDANCE CONVERTER |
| PCH163275B | CHIP TYPE IMPEDANCE CONVERTER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PCF8574P,112 | 功能描述:接口-I/O擴展器 REMOTE I/O EXPANDER RoHS:否 制造商:NXP Semiconductors 邏輯系列: 輸入/輸出端數量: 最大工作頻率:100 kHz 工作電源電壓:1.65 V to 5.5 V 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:HVQFN-16 封裝:Reel |
| PCF8574P112 | 制造商:NXP Semiconductors 功能描述:IC I/O EXPANDER 8BIT 100KHZ DIP-16 |
| PCF8574PN | 制造商:NXP Semiconductors 功能描述:IC, I/O EXPANDER, 8BIT, 100KHZ, DIP-16; Chip Configuration:8bit; Bus Frequency:100kHz; IC Interface Type:I2C; Supply Voltage Min:2.5V; Supply Voltage Max:6V; Digital IC Case Style:DIP; No. of Pins:16; No. of I/O's:8 ;RoHS Compliant: Yes |
| PCF8574PW | 功能描述:接口-I/O擴展器 Remote 8-Bit I/O Expander for I2C-Bus RoHS:否 制造商:NXP Semiconductors 邏輯系列: 輸入/輸出端數量: 最大工作頻率:100 kHz 工作電源電壓:1.65 V to 5.5 V 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:HVQFN-16 封裝:Reel |
| PCF8574PW | 制造商:Texas Instruments 功能描述:IC EXPANDER 8BIT SMD TSSOP20 |
發布緊急采購，3分鐘左右您將得到回復。