參數資料
型號: PCD3755F
廠商: NXP Semiconductors N.V.
英文描述: 8-bit microcontrollers with DTMF generator, 8 kbytes OTP and 128 bytes EEPROM
中文描述: 8 -雙音多頻發生器位微控制器,8字節OTP和128字節EEPROM
文件頁數: 17/32頁
文件大小: 200K
代理商: PCD3755F
1997 Apr 16
17
Philips Semiconductors
Product specification
8-bit microcontrollers with DTMF generator,
8 kbytes OTP and 128 bytes EEPROM
PCD3755A; PCD3755E;
PCD3755F
7.5.5
E
RASE PAGE
The EEPROM flags are set as described in Section 7.5.1.
The corresponding page bytes are erased.
The last instruction also starts Timer 2. Erasure takes
5 ms. A single-byte erase is simply a special case of ‘erase
page’.
Note that ADDR does not auto-increment after an erase
cycle.
Table 22
Erase page
7.6
Timer 2
Timer 2 is a 8-bit down-counter decremented at a rate of
1
480
×
f
xtal
. It may be used either for EEPROM timing or as
a general purpose timer. Conflicts between the two
applications should be carefully avoided.
7.6.1
T
IMER
2
FOR
EEPROM
TIMING
When used for EEPROM timing, Timer 2 serves to
generate the 5 ms intervals needed for erasing or writing
the EEPROM. At the decrement rate of
1
480
×
f
xtal
, the
reload value for a 5 ms interval is a function of f
xtal
.
Table 23 summarizes the required reload values for a
number of oscillator frequencies.
Timer 2 is started by setting bit EWP in the EPCR.
The Timer Register T2 is loaded with the reload value from
RELR. T2 decrements to zero.
For an erase/write cycle, underflow of T2 indicates the end
of the erase operation. Therefore, Timer Register T2 is
reloaded from RELR for another 5 ms interval during
which the flagged EEPROM latches are copied to the
corresponding bytes in the page addressed by ADDR.
INSTRUCTION
RESULT
MOV A, #EWP + MC3 + MC2 + MC1 ‘erase page’
control word
start ‘erase
page’ cycle
MOV EPCR, A
The second underflow of an erase/write cycle and the first
underflow of write page and erase page conclude the
corresponding EEPROM cycle. Timer 2 is stopped, T2F is
set whereas EWP and MC1 to MC3 are cleared.
Table 23
Reload values as a function of f
xtal
Note
1.
The reload value is (5
×
10
3
×
1
480
×
f
xtal
)
1;
f
xtal
in MHz.
7.6.2
T
IMER
2
AS A GENERAL PURPOSE TIMER
When used for purposes other than EEPROM timing,
Timer 2 is started by setting STT2. The Timer Register T2
(see Table 26) is loaded with the reload value from RELR.
T2 decrements to zero. On underflow, T2 is reloaded from
RELR, T2F is set and T2 continues to decrement.
Timer 2 can be stopped at any time by clearing STT2.
The value of T2 is then held and can be read out. After
setting STT2 again, Timer 2 decrements from the reload
value. Alternatively, it is possible to read T2 ‘on the fly’ i.e.
while Timer 2 is operating.
f
xtal
(MHz)
RELOAD VALUE
(1)
(HEX)
1
2
0A
14
25
3E
68
A6
3.58
6
10
16
相關PDF資料
PDF描述
PCD3755FH 8-bit microcontrollers with DTMF generator, 8 kbytes OTP and 128 bytes EEPROM
PCD3755FP 8-bit microcontrollers with DTMF generator, 8 kbytes OTP and 128 bytes EEPROM
PCD3755FT 8-bit microcontrollers with DTMF generator, 8 kbytes OTP and 128 bytes EEPROM
PCD4410 Tone/Pulse Telephone Dialer
PCD4413 Tone/Pulse Telephone Dialer
相關代理商/技術參數
參數描述
PCD3755FH 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:8-bit microcontrollers with DTMF generator, 8 kbytes OTP and 128 bytes EEPROM
PCD3755FP 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:8-bit microcontrollers with DTMF generator, 8 kbytes OTP and 128 bytes EEPROM
PCD3755FT 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:8-bit microcontrollers with DTMF generator, 8 kbytes OTP and 128 bytes EEPROM
PCD-40 制造商:Power Acoustik 功能描述:AM/FM/CD USB And SD Reader Autosound Head Unit 制造商:POWER ACOUSTIK 功能描述:AUTOSOUND HEAD UNIT AM/FM/CD USB AND SD READER
PCD-40-1050B 制造商:Mean Well 功能描述:PCD-40 series 40 W 1050 mA 38 V AC input 90-135 V Dimmable LED Driver Modules 制造商:Mean Well 功能描述:AC to DC Power Supply Enclosed LED Single Output 22-38 Volts 制造商:Mean Well 功能描述:LED POWER SUPPLY 40W 90 - 135VAC OR 180 - 295VAC IN 350 - 1750MA SLCT CURRENT