- 您現在的位置：買賣IC網 > PDF目錄367810 > PCA9674ATS (NXP SEMICONDUCTORS) Remote 8-bit I/O expander for Fm+ I2C-bus with interrupt PDF資料下載
參數資料
| 型號： | PCA9674ATS |
| 廠商： | NXP SEMICONDUCTORS |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | Remote 8-bit I/O expander for Fm+ I2C-bus with interrupt |
| 中文描述： | 8 I/O, PIA-GENERAL PURPOSE, PDSO20 |
| 封裝： | 4.40 MM, PLASTIC, MO-152, SOT266-1, SSOP-20 |
| 文件頁數： | 30/34頁 |
| 文件大?。?/td> | 179K |
| 代理商： | PCA9674ATS |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁當前第30頁第31頁第32頁第33頁第34頁
PCA9674_PCA9674A_2
NXP B.V. 2006. All rights reserved.
Product data sheet
Rev. 02 — 12 October 2006
30 of 34
NXP Semiconductors
PCA9674/74A
Remote 8-bit I/O expander for Fm+ I
2
C-bus with interrupt
16.3.2
Wave soldering
Conventional single wave soldering is not recommended for surface mount devices
(SMDs) or printed-circuit boards with a high component density, as solder bridging and
non-wetting can present major problems.
To overcome these problems the double-wave soldering method was specifically
developed.
If wave soldering is used the following conditions must be observed for optimal results:
Use a double-wave soldering method comprising a turbulent wave with high upward
pressure followed by a smooth laminar wave.
For packages with leads on two sides and a pitch (e):
–
larger than or equal to 1.27 mm, the footprint longitudinal axis is
preferred
to be
parallel to the transport direction of the printed-circuit board;
–
smaller than 1.27 mm, the footprint longitudinal axis
must
be parallel to the
transport direction of the printed-circuit board.
The footprint must incorporate solder thieves at the downstream end.
For packages with leads on four sides, the footprint must be placed at a 45
°
angle to
the transport direction of the printed-circuit board. The footprint must incorporate
solder thieves downstream and at the side corners.
During placement and before soldering, the package must be fixed with a droplet of
adhesive. The adhesive can be applied by screen printing, pin transfer or syringe
dispensing. The package can be soldered after the adhesive is cured.
Typical dwell time of the leads in the wave ranges from 3 seconds to 4 seconds at 250
°
C
or 265
°
C, depending on solder material applied, SnPb or Pb-free respectively.
A mildly-activated flux will eliminate the need for removal of corrosive residues in most
applications.
16.3.3
Manual soldering
Fix the component by first soldering two diagonally-opposite end leads. Use a low voltage
(24 V or less) soldering iron applied to the flat part of the lead. Contact time must be
limited to 10 seconds at up to 300
°
C.
When using a dedicated tool, all other leads can be soldered in one operation within
2 seconds to 5 seconds between 270
°
C and 320
°
C.
16.4 Package related soldering information
Table 12.
Mounting
Suitability of IC packages for wave, reflow and dipping soldering methods
Package
[1]
Soldering method
Wave
suitable
suitable
[3]
not suitable
Reflow
[2]
not suitable
Dipping
suitable
Through-hole mount
CPGA, HCPGA
DBS, DIP, HDIP, RDBS, SDIP, SIL
PMFP
[4]
Through-hole-surface
mount
相關PDF資料 |
PDF描述 |
|---|---|
| PCA9674N | Remote 8-bit I/O expander for Fm+ I2C-bus with interrupt |
| PCA9674TS | Remote 8-bit I/O expander for Fm+ I2C-bus with interrupt |
| PCA9674 | Remote 8-bit I/O expander for Fm+ I2C-bus with interrupt |
| PCA9674A | Remote 8-bit I/O expander for Fm+ I2C-bus with interrupt |
| PCA9675 | Remote 16-bit I/O expander for Fm+ I2C-bus with interrupt |
相關代理商/技術參數 |
參數描述 |
|---|---|
| PCA9674ATS,112 | 功能描述:接口-I/O擴展器 8-BIT I2C FM+ QB RoHS:否 制造商:NXP Semiconductors 邏輯系列: 輸入/輸出端數量: 最大工作頻率:100 kHz 工作電源電壓:1.65 V to 5.5 V 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:HVQFN-16 封裝:Reel |
| PCA9674ATS,118 | 功能描述:接口-I/O擴展器 8-BIT I2C FM+ QB RoHS:否 制造商:NXP Semiconductors 邏輯系列: 輸入/輸出端數量: 最大工作頻率:100 kHz 工作電源電壓:1.65 V to 5.5 V 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:HVQFN-16 封裝:Reel |
| PCA9674ATS-T | 功能描述:接口-I/O擴展器 8-BIT I2C FM+ QB GPIO INT PU RoHS:否 制造商:NXP Semiconductors 邏輯系列: 輸入/輸出端數量: 最大工作頻率:100 kHz 工作電源電壓:1.65 V to 5.5 V 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:HVQFN-16 封裝:Reel |
| PCA9674BS,118 | 功能描述:接口-I/O擴展器 8-BIT I2C FM+ QB RoHS:否 制造商:NXP Semiconductors 邏輯系列: 輸入/輸出端數量: 最大工作頻率:100 kHz 工作電源電壓:1.65 V to 5.5 V 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:HVQFN-16 封裝:Reel |
| PCA9674BS-T | 功能描述:接口-I/O擴展器 8-BIT I2C FM+ QB GPIO RST PU RoHS:否 制造商:NXP Semiconductors 邏輯系列: 輸入/輸出端數量: 最大工作頻率:100 kHz 工作電源電壓:1.65 V to 5.5 V 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:HVQFN-16 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。