- 您現在的位置：買賣IC網 > PDF目錄3794 > P89LPC952FBD,157 (NXP Semiconductors)IC 80C51 MCU FLASH 8K 44-LQFD PDF資料下載
參數資料
| 型號： | P89LPC952FBD,157 |
| 廠商： | NXP Semiconductors |
| 文件頁數： | 24/69頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC 80C51 MCU FLASH 8K 44-LQFD |
| 產品培訓模塊： | Migrating from 8/16-Bit MCUs to 32-Bit ARMs |
| 標準包裝： | 800 |
| 系列： | LPC900 |
| 核心處理器： | 8051 |
| 芯體尺寸： | 8-位 |
| 速度： | 18MHz |
| 連通性： | I²C，SPI，UART/USART |
| 外圍設備： | 欠壓檢測/復位，POR，PWM，WDT |
| 輸入/輸出數： | 40 |
| 程序存儲器容量： | 8KB（8K x 8） |
| 程序存儲器類型： | 閃存 |
| RAM 容量： | 512 x 8 |
| 電壓 - 電源 (Vcc/Vdd)： | 2.4 V ~ 3.6 V |
| 數據轉換器： | A/D 8x10b |
| 振蕩器型： | 內部 |
| 工作溫度： | -40°C ~ 85°C |
| 封裝/外殼： | 44-LQFP |
| 包裝： | 托盤 |
| 產品目錄頁面： | 706 (CN2011-ZH PDF) |
| 配用： | 622-1016-ND - BOARD FOR P89LPC952FA 44-PLCC 622-1008-ND - BOARD FOR LPC9103 10-HVSON OM10075-ND - EVAL BOARD FOR LPC952 568-4000-ND - DEMO BOARD SPI/I2C TO DUAL UART 568-3510-ND - DEMO BOARD SPI/I2C TO UART 622-1002-ND - USB IN-CIRCUIT PROG LPC9XX 568-1759-ND - EMULATOR DEBUGGER/PROGRMMR LPC9X |
| 其它名稱： | 568-2014-5 935280152157 P89LPC952FBD P89LPC952FDH-S |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁當前第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁
P89LPC952_954_4
NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 04 — 24 July 2008
30 of 69
NXP Semiconductors
P89LPC952/954
8-bit microcontroller with 10-bit ADC
An open-drain port pin has a Schmitt triggered input that also has a glitch suppression
circuit.
7.13.1.3
Input-only conguration
The input-only port conguration has no output drivers. It is a Schmitt triggered input that
also has a glitch suppression circuit.
7.13.1.4
Push-pull output conguration
The push-pull output conguration has the same pull-down structure as both the
open-drain and the quasi-bidirectional output modes, but provides a continuous strong
pull-up when the port latch contains a logic 1. The push-pull mode may be used when
more source current is needed from a port output. A push-pull port pin has a
Schmitt triggered input that also has a glitch suppression circuit.
7.13.2 Port 0 analog functions
The P89LPC952/954 incorporates two Analog Comparators. In order to give the best
analog function performance and to minimize power consumption, pins that are being
used for analog functions must have the digital outputs and digital inputs disabled.
Digital outputs are disabled by putting the port output into the Input-Only
(high-impedance) mode.
Digital inputs on Port 0 may be disabled through the use of the PT0AD register, bits 1:5.
On any reset, PT0AD[1:5] defaults to ‘0’s to enable digital functions.
7.13.3 Additional port features
After power-up, all pins are in Input-Only mode. Please note that this is different from
the LPC76x series of devices.
After power-up, all I/O pins except P1.5, may be congured by software.
Pin P1.5 is input only. Pins P1.2 and P1.3 are congurable for either input-only or
open-drain.
Every output on the P89LPC952/954 has been designed to sink typical LED drive current.
However, there is a maximum total output current for all ports which must not be
exceeded. Please refer to Table 11 for detailed specications.
All ports pins that can function as an output have slew rate controlled outputs to limit noise
generated by quickly switching output signals. The slew rate is factory-set to
approximately 10 ns rise and fall times.
7.14 Power monitoring functions
The P89LPC952/954 incorporates power monitoring functions designed to prevent
incorrect operation during initial power-up and power loss or reduction during operation.
This is accomplished with two hardware functions: Power-on detect and brownout detect.
7.14.1 Brownout detection
The brownout detect function determines if the power supply voltage drops below a
certain level. The default operation is for a brownout detection to cause a processor reset,
however it may alternatively be congured to generate an interrupt.
相關PDF資料 |
PDF描述 |
|---|---|
| LPC11C22FBD48/301, | IC MCU 32BIT 16KB FLASH 48LQFP |
| MC68332GCPV20 | IC MCU 32BIT 20MHZ GMASK 144LQFP |
| MC68332GCPV16 | IC MCU 32BIT 16MHZ GMASK 144LQFP |
| MC68332ACPV20 | IC MCU 32BIT 20MHZ AMASK 144LQFP |
| C8051F362-GM | IC 8051 MCU 32K FLASH 28QFN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| P89LPC954 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:8-bit microcontroller with accelerated two-clock 80C51 core 8 kB/16 kB 3 V byte-erasable flash with 10-bit ADC |
| P89LPC954FA | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:8-bit microcontroller with accelerated two-clock 80C51 core 8 kB/16 kB 3 V byte-erasable flash with 10-bit ADC |
| P89LPC954FA,529 | 功能描述:8位微控制器 -MCU 16K FL/1K RAM/512B EE/10B ADC RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| P89LPC954FBD44 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:8-bit microcontroller with accelerated two-clock 80C51 core 8 kB/16 kB 3 V byte-erasable flash with 10-bit ADC |
| P89LPC954FBD44,151 | 功能描述:8位微控制器 -MCU 16K FL/1K RAM/512B RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
發布緊急采購，3分鐘左右您將得到回復。