- 您現在的位置：買賣IC網 > PDF目錄3795 > P89LPC932A1FDH,529 (NXP Semiconductors)IC 80C51 MCU FLASH 8K 28-TSSOP PDF資料下載
參數資料
| 型號： | P89LPC932A1FDH,529 |
| 廠商： | NXP Semiconductors |
| 文件頁數： | 33/64頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC 80C51 MCU FLASH 8K 28-TSSOP |
| 標準包裝： | 51 |
| 系列： | LPC900 |
| 核心處理器： | 8051 |
| 芯體尺寸： | 8-位 |
| 速度： | 18MHz |
| 連通性： | I²C，SPI，UART/USART |
| 外圍設備： | 欠壓檢測/復位，LED，POR，PWM，WDT |
| 輸入/輸出數： | 26 |
| 程序存儲器容量： | 8KB（8K x 8） |
| 程序存儲器類型： | 閃存 |
| RAM 容量： | 768 x 8 |
| 電壓 - 電源 (Vcc/Vdd)： | 2.4 V ~ 3.6 V |
| 振蕩器型： | 內部 |
| 工作溫度： | -40°C ~ 85°C |
| 封裝/外殼： | 28-TSSOP（0.173"，4.40mm 寬） |
| 包裝： | 管件 |
| 配用： | DB-TSSOP-LPC932-ND - BOARD FOR LPC932 TSSOP 622-1014-ND - BOARD FOR LPC9XX TSSOP 622-1008-ND - BOARD FOR LPC9103 10-HVSON 622-1006-ND - SOCKET ADAPTER BOARD 622-1003-ND - KIT FOR LCD DEMO 568-1759-ND - EMULATOR DEBUGGER/PROGRMMR LPC9X 568-1758-ND - BOARD EVAL FOR LPC93X MCU FAMILY |
| 其它名稱： | 568-1286-5 935276132529 P89LPC932A1FDH-S |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁當前第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁
P89LPC932A1_3
NXP B.V. 2007. All rights reserved.
Product data sheet
Rev. 03 — 12 March 2007
39 of 64
NXP Semiconductors
P89LPC932A1
8-bit microcontroller with accelerated two-clock 80C51 core
7.23.3 Comparators and power reduction modes
Either or both comparators may remain enabled when Power-down or Idle mode is
activated, but both comparators are disabled automatically in Total Power-down mode.
If a comparator interrupt is enabled (except in Total Power-down mode), a change of the
comparator output state will generate an interrupt and wake up the processor. If the
comparator output to a pin is enabled, the pin should be congured in the push-pull mode
in order to obtain fast switching times while in Power-down mode. The reason is that with
the oscillator stopped, the temporary strong pull-up that normally occurs during switching
on a quasi-bidirectional port pin does not take place.
Comparators consume power in Power-down and Idle modes, as well as in the normal
operating mode. This fact should be taken into account when system power consumption
is an issue. To minimize power consumption, the user can disable the comparators via
PCONA.5, or put the device in Total Power-down mode.
7.24 Keypad interrupt
The Keypad Interrupt function is intended primarily to allow a single interrupt to be
generated when Port 0 is equal to or not equal to a certain pattern. This function can be
used for bus address recognition or keypad recognition. The user can congure the port
via SFRs for different tasks.
The Keypad Interrupt Mask Register (KBMASK) is used to dene which input pins
connected to Port 0 can trigger the interrupt. The Keypad Pattern Register (KBPATN) is
used to dene a pattern that is compared to the value of Port 0. The Keypad Interrupt Flag
(KBIF) in the Keypad Interrupt Control Register (KBCON) is set when the condition is
matched while the Keypad Interrupt function is active. An interrupt will be generated if
enabled. The PATN_SEL bit in the Keypad Interrupt Control Register (KBCON) is used to
dene equal or not-equal for the comparison.
In order to use the Keypad Interrupt as an original KBI function like in 87LPC76x series,
the user needs to set KBPATN = 0FFH and PATN_SEL = 1 (not equal), then any key
connected to Port 0 which is enabled by the KBMASK register will cause the hardware to
set KBIF and generate an interrupt if it has been enabled. The interrupt may be used to
wake up the CPU from Idle or Power-down modes. This feature is particularly useful in
handheld, battery-powered systems that need to carefully manage power consumption
yet also need to be convenient to use.
In order to set the ag and cause an interrupt, the pattern on Port 0 must be held longer
than six CCLKs.
相關PDF資料 |
PDF描述 |
|---|---|
| P87C51SBAA,512 | IC 80C51 MCU 4K OTP 44-PLCC |
| LPC1342FHN33,551 | IC MCU 32BIT 16KB FLASH 33HVQFN |
| LPC11U13FBD48/201, | IC MCU 32BIT 24K 48LQFP |
| LPC11C12FBD48/301, | IC MCU 32BIT 16KB FLASH 48LQFP |
| LPC11E14FBD48/401, | IC MCU 32BIT 32K 48LQFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| P89LPC932A1FHN | 制造商:NXP Semiconductors 功能描述:MCU 8BIT 80C51 8K FLASH HVQFN-28 |
| P89LPC932A1FHN,151 | 功能描述:8位微控制器 -MCU 80C51 8K FL 768B RAM RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| P89LPC932A1FHN151 | 制造商:NXP Semiconductors 功能描述:IC 8BIT MCU 80C51 18MHZ 28-HVQFN |
| P89LPC932A1FN | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:8-bit microcontroller with accelerated two-clock 80C51 core 8 kB 3 V byte-erasable flash with 512-byte data EEPROM |
| P89LPC932BA | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:80C51 8-bit microcontroller with two-clock core 8 KB 3 V low-power Flash with 512-byte data EEPROM |
發布緊急采購，3分鐘左右您將得到回復。