- 您現在的位置：買賣IC網 > PDF目錄383693 > OPA623AU Wide Bandwidth, Current-Feedback OPERATIONAL AMPLIFIER PDF資料下載
參數資料
| 型號： | OPA623AU |
| 英文描述： | Wide Bandwidth, Current-Feedback OPERATIONAL AMPLIFIER |
| 中文描述： | 寬帶，電流反饋運算放大器 |
| 文件頁數： | 14/15頁 |
| 文件大小： | 254K |
| 代理商： | OPA623AU |
14
OPA623
FIGURE 14. Mask of a Pulse Corresponding to a Binary 1 per CCITT Recommendation G.703.
0.60
0.55
0.50
0.45
0.40
0.05
–0.05
–0.40
–0.45
–0.50
–0.55
–0.60
V
1ns
0.1ns
Nominal
zero level
(2)
= Note 1.
Negative
transition
Positive transition
1ns
1ns
1.795ns
T = 7.18ns
1.795ns
3.59ns
1.35ns
1.35ns
3.59ns
1ns
0.5ns
Nominal
Pulse
0.5ns
0.1ns
NOTE: (1) The maximum “steady state” amplitude should not exceed the 0.55V limit. Overshoots and other transients are permitted to
fall into the dotted area, bounded by the amplitude levels 0.55V and 0.6V, provided that they do not exceed the steady state level by
more than 0.05V. The possibility of relaxing the amount by which the overshoot may exceed the steady state level is under study.
(2) For all measurements using these masks, the signal should be AC coupled, using a capacitor of not less than 0.01μF, to the input of
the oscilloscope used for measurements.
The nominal zero level for both masks should be aligned with the oscilloscope trace with no input signal. With the signal then applied,
the vertical position of the trace can be adjusted with the objective of meeting the limits of the masks. Any such adjustment should be
the same for both masks and should not exceed
±
0.05V. This may be checked by removing the input signal again and verifying that the
trace lies within
±
0.05V of the nominal zero level of masks.
(3) Each pulse in a coded pulse sequence should meet the limits of the relevant mask, irrespective of the state of the preceding and
succeeding pulses. For actual verification, if a 139264kHz timing signal associated with the source of the interface signal is available, its
use as a timing reference for an oscilloscope is preferred. Otherwise, compliance with the relevant mask may be tested by means of all-
0s and all-1s signals, respectively. (In practice, the signal may contain frame alignment bits per Rec. G.751.)
(4) For the purpose of these masks, the rise time and decay time should be measured between –0.4V and 0.4V, and should not exceed
2ns.
(5) The inverse pulse will have the same characteristics. Note that the timing tolerance at the zero level of the negative and positive
transitions are ±0.1ns and ±0.5n, respectively.
相關PDF資料 |
PDF描述 |
|---|---|
| OPA628AU | Low Distortion Wideband OPERATIONAL AMPLIFIER |
| OPA628 | Low Distortion Wideband OPERATIONAL AMPLIFIER |
| OPA654 | Wide Bandwidth, High Output Current Difet OPERATIONAL AMPLIFIER |
| OPA654AM | Wide Bandwidth, High Output Current Difet OPERATIONAL AMPLIFIER |
| OPA655 | Wideband, Unity Gain Stable, FET-Input OPERATIONAL AMPLIFIER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| OPA6250 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:Wideband, Unity-Gain Stable, FET-Input OPERATIONAL AMPLIFIER |
| OPA625IDBVT | 功能描述:General Purpose Amplifier 1 Circuit Rail-to-Rail SOT-23-6 制造商:texas instruments 系列:- 包裝:剪切帶（CT） 零件狀態:有效 放大器類型:通用 電路數:1 輸出類型:滿擺幅 壓擺率:115 V/μs 增益帶寬積:120MHz -3db 帶寬:- 電流 - 輸入偏置:2μA 電壓 - 輸入失調:100μV 電流 - 電源:2mA 電流 - 輸出/通道:150mA 電壓 - 電源，單/雙（±）:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 供應商器件封裝:SOT-23-6 標準包裝:1 |
| OPA627 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:Precision High-Speed Difet OPERATIONAL AMPLIFIERS |
| OPA627/637 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:High-Performance, Fully-Differential AUDIO OP AMP |
| OPA627/OPA637 | 制造商:BB 制造商全稱:BB 功能描述:OPA627. OPA637 - Precision High-Speed Difet OPERATIONAL AMPLIFIERS |
發布緊急采購，3分鐘左右您將得到回復。