- 您現在的位置：買賣IC網 > PDF目錄383693 > OPA606LM Wide-Bandwidth Difet OPERATIONAL AMPLIFIER PDF資料下載
參數資料
| 型號： | OPA606LM |
| 英文描述： | Wide-Bandwidth Difet OPERATIONAL AMPLIFIER |
| 中文描述： | 寬帶寬Difet運算放大器 |
| 文件頁數： | 8/9頁 |
| 文件大小： | 132K |
| 代理商： | OPA606LM |
8
OPA606
INPUT PROTECTION
Static damage can cause subtle changes in amplifier input
characteristics without necessarily destroying the device. In
precision operational amplifiers (both bipolar and FET types),
this may cause a noticeable degradation of offset voltage and
drift. Static protection is recommended when handling any
precision IC operational amplifier.
If the input voltage exceeds the amplifier’s negative supply
voltage, input current limiting must be used to prevent
damage.
CIRCUIT LAYOUT
Wideband amplifiers require good circuit layout techniques
and adequate power supply bypassing. Short, direct connec-
tions and good high frequency bypass capacitors (ceramic or
tantalum) will help avoid noise pickup or oscillation.
GUARDING AND SHIELDING
As in any situation where high impedances are involved,
careful shielding is required to reduce “hum” pickup in input
leads. If large feedback resistors are used, they should also
be shielded along with the external input circuitry.
Leakage currents across printed circuit boards can easily
exceed the bias current of the OPA606. To avoid leakage
problems, it is recommended that the signal input lead of the
OPA606 be wired to a Teflon
standoff. If the OPA606 is to
be soldered directly into a printed circuit board, utmost care
must be used in planning the board layout.
A “guard” pattern should completely surround the high
impedance input leads and should be connected to a low
impedance point which is at the signal input potential (see
Figure 3).
FIGURE 3. Connection of Input Guard.
APPLICATIONS CIRCUITS
FIGURE 4. Inverting Amplifier.
FIGURE 5. Noninverting Buffer.
FIGURE 2. Settling Time Test Circuit.
DUT
2
6
Scope
3
0.1%
0.1%
2k
7
4
2N4416
2N4416
100pF
3k
2k
2k
0.1%
5k
Summing
Node
V
OUT
G = –1
+15V
–15V
+15V
+5V
–5V
0.1%
5k
2
3
In
Noninverting
6
Out
2
3
In
Inverting
6
Out
2
3
In
Buffer
6
Out
OPA606
OPA606
OPA606
BOARD LAYOUT
FOR INPUT GUARDING
Guard top and bottom of board.
Alternate: use Teflon
standoff
for sensitive input pins.
Teflon
E. I. Du Pont
de Nemours & Co.
7
6
8
TO-99 Bottom View
3
2
4
5
6
7
8
1
Mini-DIP Bottom View
3
2
4
1
5
Output
+15VDC
10k
–15VDC
OPA606
BANDWIDTH > 1MHz
T
≈
1.8μsec (0.01%)
GAIN = –10V/V
Input
4
1k
3
2
7
0.1μF
0.1μF
6
Output
+15VDC
–15VDC
OPA606
Input
0.1μF
0.1μF
4
7
2
3
Bandwidth > 12MHz
Gain = +1V/V
R
IN
≈
10
13
6
相關PDF資料 |
PDF描述 |
|---|---|
| OPA622 | OPA622 - DISCONTINUED PRODUCT. No longer recommended for new design. |
| OPA622AP | OP-AMP|SINGLE|BIPOLAR|DIP|14PIN|PLASTIC |
| OPA622AU | OP-AMP|SINGLE|BIPOLAR|SOP|14PIN|PLASTIC |
| OPA623 | Wide Bandwidth, Current-Feedback OPERATIONAL AMPLIFIER |
| OPA623AP | Wide Bandwidth, Current-Feedback OPERATIONAL AMPLIFIER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| OPA606-W | 制造商:Texas Instruments 功能描述:DIE/WAFER PRODUCTS - Gel-pak, waffle pack, wafer, diced wafer on film |
| OPA615 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:Wide-Bandwidth, DC Restoration Circuit |
| OPA615ID | 功能描述:跨導放大器 Wide Bandwidth DC Restoration Circuit RoHS:否 制造商:Texas Instruments 通道數量:1 封裝 / 箱體:SOIC-14 帶寬: 輸入補償電壓:40 mV at +/- 5 V 電源電壓-最大:+/- 5 V 電源電流: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝:Tube |
| OPA615ID | 制造商:Texas Instruments 功能描述:IC DC RESTORATION CIRCUIT 14SOIC 制造商:Texas Instruments 功能描述:IC, DC RESTORATION CIRCUIT 14SOIC 制造商:Texas Instruments 功能描述:IC, DC RESTORATION CIRCUIT 14SOIC; No. of Amplifiers:1; Supply Voltage:5V; Gain Bandwidth:770MHz; Input Voltage:-3.4V to 3.4V; Amplifier Case Style:SOIC; No. of Pins:14; Slew Rate:2500V/s; Input Resistance:50ohm; Operating ;RoHS Compliant: Yes |
| OPA615ID | 制造商:Texas Instruments 功能描述:TRANSCONDUCTANCE AMPILIER IC |
發布緊急采購，3分鐘左右您將得到回復。