- 您現在的位置：買賣IC網 > PDF目錄383693 > OPA606KM END COVER; PDF資料下載
參數資料
| 型號： | OPA606KM |
| 英文描述： | END COVER; |
| 中文描述： | 寬帶寬Difet運算放大器 |
| 文件頁數： | 8/9頁 |
| 文件大?。?/td> | 132K |
| 代理商： | OPA606KM |
8
OPA606
INPUT PROTECTION
Static damage can cause subtle changes in amplifier input
characteristics without necessarily destroying the device. In
precision operational amplifiers (both bipolar and FET types),
this may cause a noticeable degradation of offset voltage and
drift. Static protection is recommended when handling any
precision IC operational amplifier.
If the input voltage exceeds the amplifier’s negative supply
voltage, input current limiting must be used to prevent
damage.
CIRCUIT LAYOUT
Wideband amplifiers require good circuit layout techniques
and adequate power supply bypassing. Short, direct connec-
tions and good high frequency bypass capacitors (ceramic or
tantalum) will help avoid noise pickup or oscillation.
GUARDING AND SHIELDING
As in any situation where high impedances are involved,
careful shielding is required to reduce “hum” pickup in input
leads. If large feedback resistors are used, they should also
be shielded along with the external input circuitry.
Leakage currents across printed circuit boards can easily
exceed the bias current of the OPA606. To avoid leakage
problems, it is recommended that the signal input lead of the
OPA606 be wired to a Teflon
standoff. If the OPA606 is to
be soldered directly into a printed circuit board, utmost care
must be used in planning the board layout.
A “guard” pattern should completely surround the high
impedance input leads and should be connected to a low
impedance point which is at the signal input potential (see
Figure 3).
FIGURE 3. Connection of Input Guard.
APPLICATIONS CIRCUITS
FIGURE 4. Inverting Amplifier.
FIGURE 5. Noninverting Buffer.
FIGURE 2. Settling Time Test Circuit.
DUT
2
6
Scope
3
0.1%
0.1%
2k
7
4
2N4416
2N4416
100pF
3k
2k
2k
0.1%
5k
Summing
Node
V
OUT
G = –1
+15V
–15V
+15V
+5V
–5V
0.1%
5k
2
3
In
Noninverting
6
Out
2
3
In
Inverting
6
Out
2
3
In
Buffer
6
Out
OPA606
OPA606
OPA606
BOARD LAYOUT
FOR INPUT GUARDING
Guard top and bottom of board.
Alternate: use Teflon
standoff
for sensitive input pins.
Teflon
E. I. Du Pont
de Nemours & Co.
7
6
8
TO-99 Bottom View
3
2
4
5
6
7
8
1
Mini-DIP Bottom View
3
2
4
1
5
Output
+15VDC
10k
–15VDC
OPA606
BANDWIDTH > 1MHz
T
≈
1.8μsec (0.01%)
GAIN = –10V/V
Input
4
1k
3
2
7
0.1μF
0.1μF
6
Output
+15VDC
–15VDC
OPA606
Input
0.1μF
0.1μF
4
7
2
3
Bandwidth > 12MHz
Gain = +1V/V
R
IN
≈
10
13
6
相關PDF資料 |
PDF描述 |
|---|---|
| OPA606KP | Wide-Bandwidth Difet OPERATIONAL AMPLIFIER |
| OPA606LM | Wide-Bandwidth Difet OPERATIONAL AMPLIFIER |
| OPA622 | OPA622 - DISCONTINUED PRODUCT. No longer recommended for new design. |
| OPA622AP | OP-AMP|SINGLE|BIPOLAR|DIP|14PIN|PLASTIC |
| OPA622AU | OP-AMP|SINGLE|BIPOLAR|SOP|14PIN|PLASTIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| OPA606KP | 功能描述:運算放大器 - 運放 Wide-Bandwidth Difet Op Amp RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比（最小值）:63 dB 輸入補償電壓:1 mV 輸入偏流（最大值）:10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel |
| OPA606KP | 制造商:BURR-BROWN 功能描述:OP AMP DIFET WIDEBAND DIP8 606 |
| OPA606KP | 制造商:Texas Instruments 功能描述:Operational Amplifier (Op-Amp) IC |
| OPA606KPG4 | 功能描述:運算放大器 - 運放 Wide-Bandwidth Difet Op Amp RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比（最小值）:63 dB 輸入補償電壓:1 mV 輸入偏流（最大值）:10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel |
| OPA606LM | 制造商:Rochester Electronics LLC 功能描述:V/I CONV. - Bulk |
發布緊急采購，3分鐘左右您將得到回復。