- 您現在的位置：買賣IC網 > PDF目錄383692 > OPA602 High-Speed Precision Difet OPERATIONAL AMPLIFIER PDF資料下載
參數資料
| 型號： | OPA602 |
| 英文描述： | High-Speed Precision Difet OPERATIONAL AMPLIFIER |
| 中文描述： | 高速精密運算放大器Difet |
| 文件頁數： | 7/9頁 |
| 文件大?。?/td> | 150K |
| 代理商： | OPA602 |
OPA602
7
COMMON-MODE REJECTION
vs FREQUENCY
140
1
Frequency (Hz)
C
10
100
1k
10k
100k
1M
10M
120
100
80
60
40
20
0
POWER SUPPLY REJECTION
vs FREQUENCY
140
1
Frequency (Hz)
P
10
100
1k
10k
100k
1M
10M
120
100
80
60
40
20
0
+
–
BIAS AND OFFSET CURRENT
vs INPUT COMMON MODE VOLTAGE
10
1
0.1
0.01
B
–15
Common-Mode Voltage (V)
10
1
0.1
0.01
O
–10
–5
0
5
10
15
Bias Current
Offset Current
BIAS AND OFFSET CURRENT
vs TEMPERATURE
10nA
B
–50
Ambient Temperature (°C)
10nA
O
–25
0
25
50
75
100
125
1nA
100
10
1
0.1
1nA
100
10
1
0.1
TYPICAL PERFORMANCE CURVES
(CONT)
T
A
= +25
°
C, V
S
=
±
15VDC unless otherwise noted.
APPLICATIONS INFORMATION
Unity-gain stability with good phase margin and excellent
output drive characteristics bring freedom from the subtle
problems associated with other high speed amplifiers. But
with any high speed, wide bandwidth circuitry, careful
circuit layout will ensure best performance. Make short,
direct interconnections and avoid stray wiring capacitance—
especially at the inverting input pin.
Power supplies should be bypassed with good high fre-
quency capacitors positioned close to the op amp pins. In
most cases 0.1
μ
F ceramic capacitors are adequate. Applica-
tions with heavier loads and fast transient waveforms may
benefit from use of additional 1.0
μ
F tantalum bypass capaci-
tors.
INPUT BIAS CURRENT GUARDING
Leakage currents across printed circuit boards can easily
exceed the input bias current of the OPA602. A circuit board
“guard” pattern (Figure 1) is an effective solution to difficult
leakage problems. This guard pattern must be repeated on all
layers of a multilayer board. By surrounding critical high
impedance input circuitry with a low impedance circuit
connection at the same potential, leakage currents will flow
harmlessly to the low impedance node.
Input bias current may also be degraded by improper han-
dling or cleaning. Contamination from handling parts and
circuit boards may be cleaned with appropriate solvents and
deionized water. Each rinsing operation should be followed
by a 30-minute bake at +85
°
C.
相關PDF資料 |
PDF描述 |
|---|---|
| OPA602AM | High-Speed Precision Difet OPERATIONAL AMPLIFIER |
| OPA602AP | High-Speed Precision Difet OPERATIONAL AMPLIFIER |
| OPA602AU | High-Speed Precision Difet OPERATIONAL AMPLIFIER |
| OPA602BM | High-Speed Precision Difet OPERATIONAL AMPLIFIER |
| OPA602BP | High-Speed Precision Difet OPERATIONAL AMPLIFIER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| OPA602AM | 制造商:Texas Instruments 功能描述: |
| OPA602AP | 功能描述:運算放大器 - 運放 High-Speed Precision Difet RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比（最小值）:63 dB 輸入補償電壓:1 mV 輸入偏流（最大值）:10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel |
| OPA602AP | 制造商:BURR-BROWN 功能描述:OP AMP DIFET PRECISION DIP8 602 |
| OPA602AP | 制造商:Texas Instruments 功能描述:Operational Amplifier (Op-Amp) IC 制造商:Texas Instruments 功能描述:IC, OP-AMP, 6.5MHZ, 35V/ us, DIP-8 |
| OPA602APG4 | 功能描述:運算放大器 - 運放 High-Speed Precision Difet RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比（最小值）:63 dB 輸入補償電壓:1 mV 輸入偏流（最大值）:10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。