參數資料
型號: OPA237
英文描述: Single-Supply Operational Amplifiers MicroAmplifier(TM) Series
中文描述: 單電源運算放大器MicroAmplifier(TM)系列
文件頁數: 9/11頁
文件大?。?/td> 255K
代理商: OPA237
9
OPA340/2340/4340
OPA340 series op amps are laser-trimmed to the reduce
offset voltage difference between the N-channel and
P-channel input stages, resulting in improved common-
mode rejection and a smooth transition between the
N-channel pair and the P-channel pair. However, within the
400mV transition region PSRR, CMRR, offset voltage,
offset drift, and THD may be degraded compared to opera-
tion outside this region.
A double-folded cascode adds the signal from the two input
pairs and presents a differential signal to the class AB output
stage. Normally, input bias current is approximately 200fA,
however, input voltages exceeding the power supplies by
more than 500mV can cause excessive current to flow in or
out of the input pins. Momentary voltages greater than
500mV beyond the power supply can be tolerated if the
current on the input pins is limited to 10mA. This is easily
accomplished with an input resistor as shown in Figure 3.
Many input signals are inherently current-limited to less
than 10mA, therefore, a limiting resistor is not required.
CAPACITIVE LOAD AND STABILITY
OPA340 series op amps can drive a wide range of capacitive
loads. However, all op amps under certain conditions may
become unstable. Op amp configuration, gain, and load
value are just a few of the factors to consider when determin-
ing stability. An op amp in unity gain configuration is the
most susceptible to the effects of capacitive load. The
capacitive load reacts with the op amp’s output resistance,
along with any additional load resistance, to create a pole in
the small-signal response which degrades the phase margin.
In unity gain, OPA340 series op amps perform well, with a
pure capacitive load up to approximately 1000pF. Increasing
gain enhances the amplifier’s ability to drive more capaci-
tance. See the typical performance curve “Small-Signal
Overshoot vs Capacitive Load.”
One method of improving capacitive load drive in the unity
gain configuration is to insert a 10
to 20
resistor in series
with the output, as shown in Figure 4. This significantly
reduces ringing with large capacitive loads. However, if
there is a resistive load in parallel with the capacitive load,
it creates a voltage divider introducing a dc error at the
output and slightly reduces output swing. This error may be
insignificant. For instance, with R
L
= 10k
and R
S
= 20
,
there is only about a 0.2% error at the output.
DRIVING A/D CONVERTERS
OPA340 series op amps are optimized for driving medium
speed (up to 100kHz) sampling A/D converters. However,
they also offer excellent performance for higher speed
converters. The OPA340 series provides an effective means
of buffering the A/D’s input capacitance and resulting
charge injection while providing signal gain.
Figures 5 and 6 show the OPA340 driving an ADS7816.
The ADS7816 is a 12-bit, micro-power sampling converter
in the tiny MSOP-8 package. When used with the minia-
ture package options of the OPA340 series, the combina-
tion is ideal for space-limited and low power applications.
For further information consult the ADS7816 data sheet.
With the OPA340 in a noninverting configuration, an RC
network at the amplifier’s output can be used to filter high
frequency noise in the signal (Figure 5). In the inverting
configuration, filtering may be accomplished with a ca-
pacitor across the feedback resistor (Figure 6).
FIGURE 3. Input Current Protection for Voltages Exceeding
the Supply Voltage.
5k
OPAx340
10mA max
V+
V
IN
V
OUT
I
OVERLOAD
RAIL-TO-RAIL OUTPUT
A class AB output stage with common-source transistors is
used to achieve rail-to-rail output. For light resistive loads
(>50k
), the output voltage is typically a few millivolts
from the supply rails. With moderate resistive loads (2k
to
50k
), the output can swing to within a few tens of milli-
volts from the supply rails and maintain high open-loop
gain. See the typical performanc curve “Output Voltage
Swing vs Output Current.”
FIGURE 4. Series Resistor in Unity-Gain Configuration Improves Capacitive Load Drive.
10
to
20
OPAx340
V+
V
IN
V
OUT
R
S
R
L
C
L
相關PDF資料
PDF描述
OPA4340EA-250 Voltage-Feedback Operational Amplifier
OPA4340EA-2500 Voltage-Feedback Operational Amplifier
OPA343OPA2343OPA4343 OPA343 OPA2343 OPA4343 - SINGLE-SUPPLY. RAIL-TO-RAIL OPERATIONAL AMPLIFIERS MicroAmplifier Series
OPA3681 Triple Wideband, Current-Feedback OPERATIONAL AMPLIFIER With Disable
OPA3681E Triple Wideband, Current-Feedback OPERATIONAL AMPLIFIER With Disable
相關代理商/技術參數
參數描述
OPA237/OPA2237/OPA4237 制造商:未知廠家 制造商全稱:未知廠家 功能描述:OPA237. OPA2237. OPA4237 - SINGLE-SUPPLY OPERATIONAL AMPLIFIERS MicroAmplifier Series
OPA237_07 制造商:BB 制造商全稱:BB 功能描述:SINGLE-SUPPLY OPERATIONAL AMPLIFIERS MicroAmplifier⑩ Series
OPA2373 制造商:BB 制造商全稱:BB 功能描述:6.5MHz, 585UA, Rail-to-Rail I/O CMOS Operational Amplifier
OPA2373AIDGSR 功能描述:運算放大器 - 運放 Dual 6.5MHz 585uA R-to-R I/O CMOS RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比(最小值):63 dB 輸入補償電壓:1 mV 輸入偏流(最大值):10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel
OPA2373AIDGSRG4 功能描述:運算放大器 - 運放 Dual 6.5MHz 585uA R-to-R I/O CMOS RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比(最小值):63 dB 輸入補償電壓:1 mV 輸入偏流(最大值):10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel