- 您現在的位置：買賣IC網 > PDF目錄1958 > NM232DDC (Murata Power Solutions Inc)ISOLATED INTERFACE DL EIA-232-D PDF資料下載
參數資料
| 型號： | NM232DDC |
| 廠商： | Murata Power Solutions Inc |
| 文件頁數： | 2/5頁 |
| 文件大?。?/td> | 0K |
| 描述： | ISOLATED INTERFACE DL EIA-232-D |
| 標準包裝： | 15 |
| 類型： | 收發(fā)器 |
| 驅動器/接收器數： | 2/2 |
| 規(guī)程： | RS232 |
| 電源電壓： | 4.5 V ~ 5.5 V |
| 安裝類型： | 通孔 |
| 封裝/外殼： | 24-DIP（0.667"，16.95mm） |
| 供應商設備封裝： | 24-DIP |
| 包裝： | 管件 |
| 產品目錄頁面： | 2721 (CN2011-ZH PDF) |
| 其它名稱： | 811-1444-5 |
NM232DDC Series
Isolated Dual EIA-232-D Transmitter and Receiver
KII_NM232DD.A04 Page 2 of 5
www.murata-ps.com/support
APPLICATION NOTES
The NM232DDC is an isolated interface device providing EIA-232-D compatibility.
A single supply from the logic side provides all necessary power for the device.
The isolation feature allows the protective or frame ground of DTEs or DCEs to
be isolated from each other, eliminating ground loop currents and inherently long
noise paths. The voltage level between different ground points can be up to ±5V
or ±6V and this level ucuates as the power taken varies. This voltage appears, in
non-isolated equipment, as normal mode noise on the signals. With such high noise
levels present it is clearly very difcult with single ended signals to have reliable
communication. Isolating the input from output so that one side oats relative to
the other allows reliable communication in environments with considerable degrees
of noise between equipments.
Figure 1 shows a typical pcb track layout with a clear separation between the logic
pin connections (pins 1-12) and the EIA-232-D connections (pins 13-24). Between
the two sides of the layout is a track which can be connected to frame or equip-
ment ground, this can be seen as the boundary between the logic and EIA-232-D
side of the device. No other rules or speed conditions need to be applied other than
to keep the two halves’ separation to a maximum.
An example of a DTE application circuit is shown in gure 2. The schematic is
illustrative of the way the NM232DDC may be connected to implement an isolated
EIA-232-D interface with a typical UART and processor bus. Precise circuitry will
depend on the application and in particular the use of the control lines shown will
need to be altered to suit the situation.
The ENABLE control line (pin 11), puts the receiver output pins 1 and 12 into a high
impedance state when set to a high level. The shutdown control line (pin 3) sets the
device into a shutdown power mode when it is at high logic level. The maximum
power drawn in shutdown mode is 50μW, a low enough level for consideration in
battery powered equipment.
Where to use the NM232DDC
The function of the NM232DDC is to provide an isolated signal path between a
UART or similar device and the EIA-232-D interface ‘D’ connector, providing two
receivers and two transmitters which can be used in a number of handshake
modes. One receiver and transmitter will normally be used for the signal lines and
the remaining pair will act as handshake lines. Figure 3 shows simply where the
device will be connected.
More complicated schemes for controlled signal interchange will require two or
more such devices. As the devices are self contained no external DC/DC converter
is required. The enable line provides a means for creating a communications bus
where each NM232DDC can have a different logical address via a decoder. This
would allow one UART to talk with many EIA-232-D connected interfaces (see
gure 4).
Figure 1
Figure 2
Figure 3
Figure 4
RoHS COMPLIANCE INFORMATION
This series is compatible with RoHS soldering systems with a peak wave solder temperature of 300C for 10 seconds. The pin termination
nish on this product series is Matte Tin over Nickel Preplate. The series is backward compatible with Sn/Pb soldering systems.
For further information, please visit www.murata-ps.com/rohs
相關PDF資料 |
PDF描述 |
|---|---|
| NM485DC | ISOLATED INTERFACE EIA-485 DL |
| NM485SLC | ISOLATED INTERFACE LP EIA-485 |
| NS3L500MTTWG | IC ETH LAN SW 2:1GB 8CH 56-WQFN |
| NS5A4684SMNTBG | IC ANLG SWITCH DUAL SPDT 10WQFN |
| NS5B1G384DFT2G | IC ANLG SWITCH SPST NC SC-70-5 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| NM232DD-T | 功能描述:RS-232接口集成電路 24P DIP RS2232 TX-RX RoHS:否 制造商:Exar 數據速率:52 Mbps 工作電源電壓:5 V 電源電流:300 mA 工作溫度范圍:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體:LQFP-100 封裝: |
| NM23CG0250 | 制造商:Micro Plastics Inc 功能描述: |
| NM24C00 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述: |
| NM24C00EM8 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:I2C Serial EEPROM |
| NM24C00EMT8 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:I2C Serial EEPROM |
發(fā)布緊急采購，3分鐘左右您將得到回復。