- 您現在的位置：買賣IC網 > PDF目錄361099 > NCP345SNT1 (ON SEMICONDUCTOR) Overvoltage Protection IC PDF資料下載
參數資料
| 型號： | NCP345SNT1 |
| 廠商： | ON SEMICONDUCTOR |
| 元件分類： | 電源管理 |
| 英文描述： | Overvoltage Protection IC |
| 中文描述： | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO5 |
| 封裝： | TSOT-23, 5 PIN |
| 文件頁數： | 2/8頁 |
| 文件大?。?/td> | 57K |
| 代理商： | NCP345SNT1 |
NCP345
http://onsemi.com
2
Figure 2. Detailed Block Diagram
+
COMP
CNTRL
(3)
OUT
(1)
GND
(2)
+
UVLO
LOGIC
BLOCK
DRIVER
Pre
regulator
V
CC
(5)
IN
(4)
ON/OFF
OUT
V5
R1
R2
R3
R4
Bandgap
Reference
V
V
CC
PIN FUNCTION DESCRIPTIONS
Pin #
Symbol
Pin Description
1
OUT
This signal drives the gate of a Pchannel MOSFET. It is controlled by the voltage level on IN or the logic state
of the CNTRL input. When an overvoltage event is detected, the OUT pin is driven to within 1.0 V of V
CC
in
less than 1.0 sec provided that gate and stray capacitance is less than 12 nF.
2
GND
Circuit Ground
3
CNTRL
This logic signal is used to control the state of OUT and turnon/off the Pchannel MOSFET. A logic High
results in the OUT signal being driven to within 1.0 V of V
CC
which disconnects the FET. If this pin is not used,
the input should be connected to ground.
4
IN
This pin senses an external voltage point. If the voltage on this input rises above the overvoltage threshold
(VTH), the OUT pin will be driven to within 1.0 V of V
CC
, thus disconnecting the FET. The nominal threshold
level is 6.85 V and this threshold level can be increased with the addition of an external resistor between IN
and V
CC
.
5
V
CC
Positive Voltage supply. If V
CC
falls below 2.8 V (nom), the OUT pin will be driven to within 1.0 V of V
CC
, thus
disconnecting the Pchannel FET.
TRUTH TABLE
IN
CNTRL
OUT
<V
th
L
GND
<V
th
H
V
CC
>V
th
L
V
CC
>V
th
H
V
CC
相關PDF資料 |
PDF描述 |
|---|---|
| NCP1651DR2 | Single Stage Power Factor Controller |
| NCP1651 | Single Stage Power Factor Controller |
| NCP1651DR2G | Single Stage Power Factor Controller |
| NCP345SNT1G | Overvoltage Protection IC |
| NCP346SN1T1G | Overvoltage Protection IC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| NCP345SNT1G | 功能描述:監控電路 6.85V OVP Supervisor RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
| NCP346SN1EVB | 功能描述:電源管理IC開發工具 ANA NCP346 EVAL BD RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
| NCP346SN1T1G | 功能描述:監控電路 4.45V Overvoltage Supervisor RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
| NCP346SN2T1G | 功能描述:監控電路 5.5V Overvoltage Supervisor RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
| NCP347AE AV51D WAF | 制造商:ON Semiconductor 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。