- 您現在的位置：買賣IC網 > PDF目錄361091 > NCP1381 (ON SEMICONDUCTOR) Low−Standby High Performance PWM Controller PDF資料下載
參數資料
| 型號： | NCP1381 |
| 廠商： | ON SEMICONDUCTOR |
| 英文描述： | Low−Standby High Performance PWM Controller |
| 文件頁數： | 8/26頁 |
| 文件大小： | 559K |
| 代理商： | NCP1381 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁當前第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁
NCP1381
http://onsemi.com
8
Figure 5. A Typical Startup Sequence Followed by a Faulty Condition
Startup Resistor Calculation
For the sake of the example, we will go through the
calculation of the startup element. Suppose that we have the
following information:
VCC
ON
= 15 V.
VCC
OFF
= 10 V.
I
CC2
= 4 mA, given by the selected MOSFET Q
g
.
Startup duration below 2 s at minimum input voltage.
Input voltage from 85 VAC to 265 VAC.
Standby power below 500 mW.
1. From a startup V of 15 10 = 5 V and a 4 mA
total consumption, we can obtain the necessary
V
CC
capacitor to keep enough voltage, assuming
the feedback loop is closed within 10ms: CV
CC
=
4 m x 10 m / 5 = 8 F or 22 F for the normalized
value if we account for the natural dispersion.
2. If we want a startup below 2 s, then the charging
current flowing inside the V
CC
capacitor must be
above: I
charge
> 15 x 22 u / 2 > 165 A. If we add
the 15 A of I
CC1
, the total startup current shall be
above 180 A.
3. The minimum input voltage is 85 x 1.414 = 120 V.
Then, R
startup
should be below (120 15) / 180
< 580 k .
4. From this value, we can calculate the dissipated
power at high line: P
startup
= (265 x 1.414)
2
/ 580 k
= 242 mW.
In latched mode, an internal zener diode is activated and
clamps V
CC
to around 6 V. When V
CC
goes below 4 V, this
zener is relaxed and the circuit can startup again.
Please note that in fault mode the V
CC
comparator has the
priority and stops the pulses anytime V
CC
falls below its
minimum operating level VCC
OFF
.
相關PDF資料 |
PDF描述 |
|---|---|
| NCP1381DR2G | Low−Standby High Performance PWM Controller |
| NCP1395APG | High Performance Resonant Mode Controller |
| NCP1395ADR2G | High Performance Resonant Mode Controller |
| NCP1395BDR2G | High Performance Resonant Mode Controller |
| NCP1395BPG | High Performance Resonant Mode Controller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| NCP1381 AM90 WAF | 制造商:ON Semiconductor 功能描述: |
| NCP1381ADAPEVB | 功能描述:BOARD EVAL NCP1381 RoHS:是 類別:編程器，開發系統 >> 評估演示板和套件 系列:* 標準包裝:1 系列:PCI Express® (PCIe) 主要目的:接口，收發器，PCI Express 嵌入式:- 已用 IC / 零件:DS80PCI800 主要屬性:- 次要屬性:- 已供物品:板 |
| NCP1381DR2G | 功能描述:電流型 PWM 控制器 ANA PWM CONTROLLER RoHS:否 制造商:Texas Instruments 開關頻率:27 KHz 上升時間: 下降時間: 工作電源電壓:6 V to 15 V 工作電源電流:1.5 mA 輸出端數量:1 最大工作溫度:+ 105 C 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-14 |
| NCP1382DR2G | 功能描述:電流型 PWM 控制器 L-STNDBY PWM CNTRLR RoHS:否 制造商:Texas Instruments 開關頻率:27 KHz 上升時間: 下降時間: 工作電源電壓:6 V to 15 V 工作電源電流:1.5 mA 輸出端數量:1 最大工作溫度:+ 105 C 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-14 |
| NCP1392B | 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:High-Voltage Half-Bridge Driver with Inbuilt Oscillator |
發布緊急采購，3分鐘左右您將得到回復。