- 您現在的位置：買賣IC網 > PDF目錄1956 > NCN7200MTTWG (ON Semiconductor)IC MUX/DEMUX OCTAL 1X2 42WQFN PDF資料下載
參數資料
| 型號： | NCN7200MTTWG |
| 廠商： | ON Semiconductor |
| 文件頁數： | 6/10頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC MUX/DEMUX OCTAL 1X2 42WQFN |
| 標準包裝： | 2,000 |
| 功能： | 多路復用器/解復用器、千兆位以太網 LAN |
| 電路： | 8 x 1:2 |
| 導通狀態電阻： | 16 歐姆 |
| 電壓電源： | 單電源 |
| 電壓 - 電源，單路/雙路(±)： | 3 V ~ 3.6 V |
| 電流 - 電源： | 1mA |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 42-WFQFN 裸露焊盤 |
| 供應商設備封裝： | 42-WQFN-EP（3.5x9.0） |
| 包裝： | 帶卷 (TR) |
NCN7200
http://onsemi.com
5
GIGABIT ETHERNET LAN SWITCH WITH 2:1 MUX/ DEMUX AND POWER DOWN FEATURE
(Min / Max values are at VDD = 3.3 V ±10%, TA = 40°C to +85°C. Typ values are at VDD = 3.3 V and TA = 25°C)
Symbol
Unit
Max
Typ
Min
Test Conditions
Description
CONTROL LOGIC (SEL AND PD PINS) DC ELECTRICAL CHARACTERISTICS FOR 1000 BASET ETHERNET SWITCHING
VIH
Input HIGH Voltage
Guaranteed HIGH level
2.0
V
VIL
Input LOW Voltage
Guaranteed LOW level
0.5
0.8
VIK
Clamp Diode Voltage
VDD = Max, IIN = 18 mA
0.7
1.0
IIHSEL
Input HIGH Current (SEL)
VDD = Max, VIN = VDD
±0.1
mA
IIHPD
Input High Current (PD)
VDD = Max, VIN = VDD
±1.2
IIL
Input LOW Current
VDD = Max, VIN = GND
±0.1
IOFF
OffLeakage Current (SEL)
VDD = 0 V, VIN = 0 V to VDD
±0.1
DATA PATH (AX TO BX, CX PINS) DC ELECTRICAL CHARACTERISTICS FOR 1000 BASET ETHERNET SWITCHING
RON
Switch OnResistance (Note 3)
VDD = Min, 1.5 V < VIN < VDD, ITN = 40 mA
2.0
6.0
W
RFLAT(ON)
OnResistance Flatness (Note 3)
VDD = Min, VIN @ 1.5 V and VDD, ITN =
40 mA
0.3
DRON
OnResistance match from center
ports to any other port (Note 3)
VDD = Min, 1.5 V < VIN < VDD, ITN = 40 mA
0.5
1.0
ION
On Leakage Current (AX)
VDD = 3.6 V, VAX = 0 V or VDD, VOUT = Float
0.1
+0.1
mA
IOFF
Off Leakage Current (AX/BX/CX)
VDD = 3.6 V, VIN = 0 V or VDD, VOUT = VDD or
0 V
0.1
+0.1
mA
DATA PATH (LEDAX TO LEDBX, LEDCX PINS) DC ELECTRICAL CHARACTERISTICS FOR 1000 BASET ETHERNET
SWITCHING
RON
Switch OnResistance (Note 3)
VDD = Min, 1.5 V < VIN < VDD, ITN = 40 mA
7.0
16
W
RFLAT(ON)
OnResistance Flatness (Note 3)
VDD = Min, VIN @ 1.5 V and VDD, ITN =
40 mA
0.3
DRON
OnResistance match from center
ports to any other port (Note 3)
VDD = Min, 1.5 V < VIN < VDD, ITN = 40 mA
0.8
1.25
ION
On Leakage Current (LEDAX)
VDD = 3.6 V, VAX = 0 V or VDD, VOUT = Float
0.1
+0.1
mA
IOFF
Off Leakage Current
(LEDAX/LEDBX/LEDCX)
VDD = 3.6 V, VIN = 0 V or VDD, VOUT = VDD or
0 V
0.1
+0.1
mA
CONTROL LOGIC (SEL AND PD PINS) DC ELECTRICAL CHARACTERISTICS FOR 10/100 BASET ETHERNET SWITCHING
VIH
Input HIGH Voltage
Guaranteed HIGH level (Control Pins)
2.0
V
VIL
Input LOW Voltage
Guaranteed LOW level (Control Pins)
0.5
0.8
VIK
Clamp Diode Voltage
VDD = Max, IN = 18 mA
0.7
1.0
IIHSEL
Input HIGH Current (SEL)
VDD = Max, VIN = VDD
±0.1
mA
IIHPD
Input HIGH Current (PD)
VDD = Max, VIN = VDD
±1.2
IIL
Input LOW Current
VDD = Max, VIN = GND
±0.1
IOFF
OffLeakage Current (SEL)
VDD = 0 V, VIN = 0 V to VDD
±0.1
2. Active power represents normal data communication. Standby power is when the device is enabled for operation but there is no LAN traffic
(cable not connected). Power down current is the minimum power state used when not connected and mobile.
3. Measured by the voltage drop between A and B pins at indicated current through the switch. ON resistance is determined by the lower
of the voltages on the two (A & B) pins.
4. Guaranteed by design and/or characterization.
5. The bus switch contributes no propagational delay other than the RC delay of the ON resistance of the switch and the load capacitance.
The time constant for the switch alone is of the order of 0.25 ns for 10 pF load. Since this time constant is much smaller than the rise/fall
times of typical driving signals, it adds very little propagational delay to the system. Propagational delay of the bus switch when used in
a system is determined by the driving circuit on the driving side of the switch and its interactions with the load on the driven side.
相關PDF資料 |
PDF描述 |
|---|---|
| NCN8024DTBR2G | SMART CARD IC 5V/3V TSSOP |
| NCN8024RDWR2G | IC SMART CARD IC2 28SOIC |
| NCN8025MTTBG | IC SMART CARD I2C 16-QFN |
| NCN9252MUTAG | IC USB SWITCH DP3T 12UQFN |
| NCP1092DBRG | IC CTLR IEEE 802.3AF 8-TSSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| NCN7201MTTWG | 制造商:ON Semiconductor 功能描述:LAN SWITCH - Tape and Reel 制造商:ON Semiconductor 功能描述:REEL / LAN SWITCH |
| NCN8024 | 制造商:ONSEMI 制造商全稱:ON Semiconductor 功能描述:Smart Card Interface IC |
| NCN8024D | 制造商:ON Semiconductor 功能描述: |
| NCN8024D-EVB | 制造商:ON Semiconductor 功能描述:Evaluation board for 3V/5V Smart Card Interface 制造商:P&S 功能描述:Evaluation board for 3V/5V Smart Card Interface |
| NCN8024DTBR2G | 功能描述:接口 - 專用 SMART CARD IC 3ST 8INPUT RoHS:否 制造商:Texas Instruments 產品類型:1080p60 Image Sensor Receiver 工作電源電壓:1.8 V 電源電流:89 mA 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:BGA-59 |
發布緊急采購，3分鐘左右您將得到回復。