- 您現在的位置：買賣IC網 > PDF目錄299526 > MX216-38-500-G-R18 SINGLE, 2 CHANNELS, ROTARY OPTICAL POSITION ENCODER PDF資料下載
參數資料
| 型號： | MX216-38-500-G-R18 |
| 元件分類： | 編、解碼器及復用、解復用 |
| 英文描述： | SINGLE, 2 CHANNELS, ROTARY OPTICAL POSITION ENCODER |
| 文件頁數： | 2/3頁 |
| 文件大小： | 155K |
| 代理商： | MX216-38-500-G-R18 |
Tel: 805-968-0782 /800-350-2727 | Fax: 805-968-3154 /800-960-2726 | 7230 Hollister Ave., Goleta, CA 93117-2807 | www.beiied.com
Specification No. 02122-001 Rev11-10
Preparation:
1.
Inspect motor interface per MX21 Data Sheet or specification drawing.
2.
Motor shaft must be free of burrs & other surface defects.
Installation:
1.
Motor shaft should NOT be rotating during initial encoder installation.
2.
Hold encoder perpendicular to motor shaft. Guide the encoder onto the motor shaft,
pushing encoder STRAIGHT on until it is flush against the mount surface. Do NOT
rock side to side.
3.
Install two #4-40 mount screws. Do not fully tighten at this point. (Note: A thread
sealant should be applied to the screw threads)
4.
Rotate the motor shaft (300 RPM, minimum). Press the air-gap button until it
bottoms to the top of the encoder momentarily, then release. CAUTION: DO NOT
press air-gap button while motor shaft is stationary. Button should only be pressed
for one or two seconds while shaft is rotating.
5.
Tighten mounting screws fully. (recommended torque is 30 to 40 ounce inches.)
6.
This completes the mechanical installation. Proceed with electrical connections as
indicated on product data sheet or specification drawing.
Removal:
1.
Motor shaft may be stationary or rotating up to 1000 RPM during encoder removal.
2.
Remove two mounting screws.
3.
Grasp encoder firmly and pull STRAIGHT off of the motor shaft. Do NOT rock side
to side.
Dimensions
BEI Sensors
Output
Waveform
MX21 INSTA-MOUNT Series—Modular
Incremental Rotary Optical Encoder
Figure 3
Terminations
CCW ROTATION OF SHAFT
MX212 outputs A & B ONLY
MX213 outputs A, B & INDEX ONLY
MX216 outputs as shown
360°E NOM
180°E NOM
90°E NOM
A
B
INDEX
INDEX GATED TO A&B
90°E TO 450°E
INDEX UNGATED
Installation
Instructions
These commodities, technology or software if exported from the United States must be in accordance with the Bureau of
Industry, and Security, Export Administration regulations. Diversion contrary to U.S law is prohibited.
相關PDF資料 |
PDF描述 |
|---|---|
| MX216-6M-1000-G-C18 | SINGLE, 2 CHANNELS, ROTARY OPTICAL POSITION ENCODER |
| MX213-6M-200-U-C18 | SINGLE, 2 CHANNELS, ROTARY OPTICAL POSITION ENCODER |
| MX216-6M-512-U-R18 | SINGLE, 2 CHANNELS, ROTARY OPTICAL POSITION ENCODER |
| MX213-25-200-U-R18 | SINGLE, 2 CHANNELS, ROTARY OPTICAL POSITION ENCODER |
| MX213-38-1024-U-R18 | SINGLE, 2 CHANNELS, ROTARY OPTICAL POSITION ENCODER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MX216-38-500-U | 功能描述:編碼器 0.375" BORE 500PPR RoHS:否 制造商:Avago Technologies 產品:Optical Encoders 類型:Absolute 每轉脈沖: 制動器數量: 通道數量:2 安裝風格:Through Hole 端接類型:Solder Pin 輸出: 軸類型: 帶開關: 電源電壓:5 V 工作溫度范圍:- 40 C to + 115 C |
| MX216-38-512-U | 功能描述:編碼器 0.375" BORE 512PPR RoHS:否 制造商:Avago Technologies 產品:Optical Encoders 類型:Absolute 每轉脈沖: 制動器數量: 通道數量:2 安裝風格:Through Hole 端接類型:Solder Pin 輸出: 軸類型: 帶開關: 電源電壓:5 V 工作溫度范圍:- 40 C to + 115 C |
| MX216-50-1000-U | 功能描述:編碼器 0.5" BORE 1000PPR RoHS:否 制造商:Avago Technologies 產品:Optical Encoders 類型:Absolute 每轉脈沖: 制動器數量: 通道數量:2 安裝風格:Through Hole 端接類型:Solder Pin 輸出: 軸類型: 帶開關: 電源電壓:5 V 工作溫度范圍:- 40 C to + 115 C |
| MX216-50-1024-U | 功能描述:編碼器 0.5" BORE 1024PPR RoHS:否 制造商:Avago Technologies 產品:Optical Encoders 類型:Absolute 每轉脈沖: 制動器數量: 通道數量:2 安裝風格:Through Hole 端接類型:Solder Pin 輸出: 軸類型: 帶開關: 電源電壓:5 V 工作溫度范圍:- 40 C to + 115 C |
| MX216-50-500-U | 功能描述:編碼器 0.5" BORE 500PPR RoHS:否 制造商:Avago Technologies 產品:Optical Encoders 類型:Absolute 每轉脈沖: 制動器數量: 通道數量:2 安裝風格:Through Hole 端接類型:Solder Pin 輸出: 軸類型: 帶開關: 電源電壓:5 V 工作溫度范圍:- 40 C to + 115 C |
發布緊急采購，3分鐘左右您將得到回復。