- 您現在的位置：買賣IC網 > PDF目錄383642 > MT8930C (Mitel Networks Corporation) Subscriber Network Interface Circuit(用戶網絡接口電路（提供點到點或點到多點數字傳送）) PDF資料下載
參數資料
| 型號： | MT8930C |
| 廠商： | Mitel Networks Corporation |
| 英文描述： | Subscriber Network Interface Circuit(用戶網絡接口電路（提供點到點或點到多點數字傳送）) |
| 中文描述： | 用戶網絡接口電路（用戶網絡接口電路（提供點到點或點到多點數字傳送）） |
| 文件頁數： | 4/42頁 |
| 文件大小： | 323K |
| 代理商： | MT8930C |
第1頁第2頁第3頁當前第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁
MT8930C
Pin Description (continued)
Pin #
Name
DIP
PLCC
9-36
17
26
SYNC/BA
Synchronization/Bus Activity Output (Cmode = 0):
output indicating synchronization
to incoming RX frames when activation request is asserted and the deactivation request
is ’0’ (AR = 1 and DR = 0). Synchronization is declared once three successive frames
conforming to the 14-bit bipolar violation criteria have been detected. If part is
deactivated or activation request is ’0’ (AR = 0 or DR = 1), this pin indicates the
presence of bus activity.
MFR
Multiframe Input/Output (Cmode=0):
multiframe input in NT mode or output in TE
mode. Setting this pin to one in NT mode when HALF = 1, forces the F
A
, N pair to 1, 0
respectively. This pin going high in TE mode indicates that F
A
= 1 & N= 0 has been
received. This signal is updated on the rising edge of the HALF signal.
MCH
Maintenance Channel (Q-channel) Input/Output (Cmode=0):
an output in NT mode
which is valid only in the frame following the transmission of MFR. In TE mode, this is
the maintenance channel (Q-channel) input which is transmitted in the F
A
and L bits
following the reception of the multiframe signal. This input is sampled on the falling
edge of the HALF signal.
M/S
M/S Input/Output (Cmode=0):
M/S bit input in NT mode or M/S bit output in TE mode.
M is read or written when HALF=1 while S is read or written when HALF=0.
AR
Activate Request Input (Cmode = 0):
asserting AR with DR = 0 will initiate the
appropriate S-interface activation sequence coded in the NT or TE activation/
deactivation controller.
DR
Deactivate Request Input (Cmode = 0):
asserting DR high will initiate the appropriate
S-interface deactivation sequence coded in the NT or TE activation/ deactivation
controller.
18
30
19
31
20
32
21
34
22
35
23
37
Rsti
Reset Input:
Schmitt trigger reset input. If ’0’, sets all control registers to the default
conditions, resets activation state machines to the deactivated state, resets HDLC,
clears the HDLC FIFO‘s. Sets the microport to Motorola bus mode.
24
38
STAR/Rsto
Star/Reset (Open Drain Output):
192kbit/s Rx data output fixed relative to the ST-
BUS timebase. A group of NTs, in fixed timing mode, can be wire or’ed together to
create a Star configuration. Active low reset output in TE mode indicating 128
consecutive marks have been received. Can be connected directly to Rsti to allow NT
to reset all TEs on the bus. This pin must be tied to V
DD
with a 10 k
resistor.
LRx
Receive Line Signal Input:
this is a high impedance input for the pseudoternary line
signal to be connected to the line through a 2:1 ratio transformer. See Figures 20 and
21. A DC bias level on this input equal to V
Bias
must be maintained.
LTx
Transmit Line Signal Output:
this is a current source output designed to drive a
nominal 50 ohm line through a 2:1 ratio transformer. See Figures 20 and 21.
V
Bias
Bias Voltage:
analog ground for Tx and Rx transformers. This pin must be decoupled
to V
through a 10
μ
F capacitor with good high frequency characteristics (i.e.,
tantalum).
V
DD
Power Supply Input.
NC
No Connection.
25
40
26
42
27
43
28
44
1,5-6,10-
12,15,18,
23,27-
29, 33,
36, 39, 41
Description
相關PDF資料 |
PDF描述 |
|---|---|
| MT8930 | CMOS ST-BUS⑩ FAMILY Subscriber Network Interface Circuit Preliminary Information |
| MT8930C | CMOS ST-BUS⑩ FAMILY Subscriber Network Interface Circuit Preliminary Information |
| MT8930CC | CMOS ST-BUS⑩ FAMILY Subscriber Network Interface Circuit Preliminary Information |
| MT8930CE | CMOS ST-BUS⑩ FAMILY Subscriber Network Interface Circuit |
| MT8930CP | CMOS ST-BUS⑩ FAMILY Subscriber Network Interface Circuit |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MT8930C-1 | 制造商:MITEL 制造商全稱:Mitel Networks Corporation 功能描述:CMOS ST-BUS⑩ FAMILY Subscriber Network Interface Circuit |
| MT8930CC | 制造商:MITEL 制造商全稱:Mitel Networks Corporation 功能描述:CMOS ST-BUS⑩ FAMILY Subscriber Network Interface Circuit Preliminary Information |
| MT8930CE | 制造商:ZARLINK 制造商全稱:Zarlink Semiconductor Inc 功能描述:Subscriber Network Interface Circuit |
| MT8930CP | 制造商:ZARLINK 制造商全稱:Zarlink Semiconductor Inc 功能描述:Subscriber Network Interface Circuit |
| MT8930CPR | 制造商:Microsemi Corporation 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。