參數資料
型號： MT8880CP-1
廠商： Mitel Networks Corporation
英文描述： ISO2-CMOS Integrated DTMFTransceiver
中文描述： ISO2 - CMOS集成DTMFTransceiver
文件頁數： 10/18頁
文件大?。?/td> 312K
代理商： MT8880CP-1
MT8880C/MT8880C-1
ISO
2
-CMOS
4-42
Table 6
.
Control Register B Description
Table 7. Status Register Description
BIT
NAME
FUNCTION
DESCRIPTION
b0
BURST
BURST MODE
A logic ‘0’ enables the burst mode. When this mode is
selected, data corresponding to the desired DTMF tone pair
can be written to the Transmit Register resulting in a tone
burst of a specific duration (see AC Characteristics).
Subsequently, a pause of the same duration is induced.
Immediately following the pause, the Status Register is
updated indicating that the Transmit Register is ready for
further instructions and an interrupt will be generated if the
interrupt mode has been enabled. Additionally, if call
progress (CP) mode has been enabled, the burst and pause
duration is increased by a factor of two. When the burst
mode is not selected (logic ‘1’) tone bursts of any desired
duration may be generated.
b1
TEST
TEST MODE
By enabling the test mode (logic’1’), the IRQ/CP pin will
present the delayed steering (inverted) signal from the DTMF
receiver. Refer to Figure 9 (b3 waveform) for details
concerning the output waveform. DTMF mode must be
selected (CRA b1=0) before test mode can be implemented.
b2
S/D
SINGLE /DUAL TONE
GENERATION
A logic ‘0’ will allow Dual Tone Multi-Frequency signals to be
produced. If single tone generation is enabled (logic ‘1’),
either row or column tones (low group or high group) can be
generated depending on the state of b3 in Control Register
B.
b3
C/R
COLUMN/ROW TONES
When used in conjunction with b2 (above) the transmitter
can be made to generate single row or single column
frequencies. A logic ‘0’ will select row frequencies and a logic
‘1’ will select column frequencies.
BIT
NAME
STATUS FLAG SET
STATUS FLAG CLEARED
b0
IRQ
Interrupt has occurred. Bit one (b1)
or bit two (b2) is set.
Interrupt is inactive. Cleared after
Status Register is read.
b1
TRANSMIT DATA
REGISTER EMPTY
(BURST MODE ONLY)
Pause duration has terminated
and transmitter is ready for new
data.
Cleared after Status Register is
read or when in non-burst mode.
b2
RECEIVE DATA
REGISTER FULL
Valid data is in the Receive Data
Register.
Cleared after Status Register is
read.
b3
DELAYED STEERING
Set upon the valid detection of the
absence of a DTMF signal.
Cleared upon the detection of a
valid DTMF signal.
相關PDF資料
PDF描述
MT8880CS-1 ISO2-CMOS Integrated DTMFTransceiver
MT8880C Integrated DTMF Transceiver(雙音多頻信號（DTMF）收發器（帶電話程序?yàn)V波器）)
MT8885AE Integrated DTMFTransceiver with Power Down & Adaptive Micro Interface
MT8885AN Integrated DTMFTransceiver with Power Down & Adaptive Micro Interface
MT8885AP Integrated DTMFTransceiver with Power Down & Adaptive Micro Interface
相關代理商/技術參數
參數描述
MT8880CPR 制造商:Microsemi Corporation 功能描述: 制造商:Microsemi Corporation 功能描述:DTMF TXRX 3.58MHZ CMOS 5V 28PLCC - Tape and Reel
MT8880CPR1 制造商:Microsemi Corporation 功能描述:PB FREE INTEGRATED DTMF TRANSCEIVER 制造商:Microsemi Corporation 功能描述:DTMF TXRX 3.58MHZ CMOS 5V 28PLCC - Tape and Reel 制造商:MICROSEMI CONSUMER MEDICAL PRODUCT GROUP 功能描述:IC TXRX DTMF 28PLCC 制造商:Microsemi Corporation 功能描述:IC TXRX DTMF 28PLCC
MT8880CS 制造商:Microsemi Corporation 功能描述:DTMF TXRX 3.58MHZ CMOS 5V 20SOIC - Rail/Tube
MT8880CS/CS-1 制造商:MITEL 制造商全稱:Mitel Networks Corporation 功能描述:Integrated DTMFTransceiver
MT8880CS1 制造商:Microsemi Corporation 功能描述:DTMF TXRX 3.58MHz CMOS 5V 20-Pin SOIC Tube 制造商:Microsemi Corporation 功能描述:DTMF TXRX 3.58MHZ CMOS 5V 20SOIC - Rail/Tube 制造商:Microsemi Corporation 功能描述:PB FREE DTMF TRANSCEIVER
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*