- 您現在的位置：買賣IC網 > PDF目錄384756 > MT48LC8M16A2TG-75IT (Micron Technology, Inc.) SYNCHRONOUS DRAM PDF資料下載
參數資料
| 型號： | MT48LC8M16A2TG-75IT |
| 廠商： | Micron Technology, Inc. |
| 英文描述： | SYNCHRONOUS DRAM |
| 中文描述： | 同步DRAM |
| 文件頁數： | 19/59頁 |
| 文件大?。?/td> | 1822K |
| 代理商： | MT48LC8M16A2TG-75IT |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁當前第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁
19
128Mb: x4, x8, x16 SDRAM
128MSDRAM_E.p65
–
Rev. E; Pub. 1/02
Micron Technology, Inc., reserves the right to change products or specifications without notice.
2001, Micron Technology, Inc.
128Mb: x4, x8, x16
SDRAM
Data from any READ burst may be truncated with a
subsequent WRITE command, and data from a fixed-
length READ burst may be immediately followed by data
from a WRITE command (subject to bus turnaround
limitations). The WRITE burst may be initiated on the
clock edge immediately following the last (or last de-
sired) data element from the READ burst, provided that I/
O contention can be avoided. In a given system design,
there may be a possibility that the device driving the
input data will go Low-Z before the SDRAM DQs go High-
Z. In this case, at least a single-cycle delay should occur
between the last read data and the WRITE command.
The DQM input is used to avoid I/O contention, as
shown in Figures 9 and 10. The DQM signal must be
asserted (HIGH) at least two clocks prior to the WRITE
command (DQM latency is two clocks for output buffers)
DON
’
T CARE
READ
NOP
NOP
NOP
NOP
DQM
CLK
DQ
D
OUT
n
T2
T1
T4
T3
T0
COMMAND
ADDRESS
BANK,
COL
n
WRITE
D
IN
b
BANK,
COL
b
T5
DS
t
HZ
t
NOTE:
A CAS latency of three is used for illustration. The
READ command
may be to any bank, and the WRITE command may be to any bank.
Figure 10
READ to WRITE With
Extra Clock Cycle
Figure 9
READ to WRITE
READ
NOP
NOP
WRITE
NOP
CLK
T2
T1
T4
T3
T0
DQM
DQ
D
OUT
n
COMMAND
D
IN
b
ADDRESS
COL
n
COL
b
DS
t
HZ
t
t
CK
NOTE:
A CAS latency of three is used for illustration. The
READ
command may be to any bank, and the WRITE command
may be to any bank. If a burst of one is used, then DQM is
not required.
to suppress data-out from the READ. Once the WRITE
command is registered, the DQs will go High-Z (or re-
main High-Z), regardless of the state of the DQM signal,
provided the DQM was active on the clock just prior to
the WRITE command that truncated the READ com-
mand. If not, the second WRITE will be an invalid WRITE.
For example, if DQM was LOW during T4 in Figure 10,
then the WRITEs at T5 and T7 would be valid, while the
WRITE at T6 would be invalid.
The DQM signal must be de-asserted prior to the
WRITE command (DQM latency is zero clocks for input
buffers) to ensure that the written data is not masked.
Figure 9 shows the case where the clock frequency allows
for bus contention to be avoided without adding a NOP
cycle, and Figure 10 shows the case where the additional
NOP is needed.
相關PDF資料 |
PDF描述 |
|---|---|
| MT48LC8M16A2TG-75L | SYNCHRONOUS DRAM |
| MT48LC8M16A2TG-75LIT | SYNCHRONOUS DRAM |
| MT48LC8M16A2TG-7E | SYNCHRONOUS DRAM |
| MT48LC8M16A2TG-7EIT | SYNCHRONOUS DRAM |
| MT48LC8M16A2TG-7EL | SYNCHRONOUS DRAM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MT48LC8M16A2TG75ITG | 制造商:Micron Technology Inc 功能描述: |
| MT48LC8M16A2TG-75L | 制造商:MICRON 制造商全稱:Micron Technology 功能描述:SYNCHRONOUS DRAM |
| MT48LC8M16A2TG-75LIT | 制造商:MICRON 制造商全稱:Micron Technology 功能描述:SYNCHRONOUS DRAM |
發布緊急采購，3分鐘左右您將得到回復。