- 您現在的位置：買賣IC網 > PDF目錄374507 > MS3475L12-32SW (ITT Corporation) Series 2 Connectors PV PDF資料下載
參數資料
| 型號： | MS3475L12-32SW |
| 廠商： | ITT Corporation |
| 英文描述： | Series 2 Connectors PV |
| 中文描述： | 光伏連接器系列2 |
| 文件頁數： | 10/10頁 |
| 文件大?。?/td> | 500K |
| 代理商： | MS3475L12-32SW |
www.ittcannon.com
Dimensions are shown in inches (millimeters).
Dimensions subject to change.
MIL-C-26482, Series 2 Connectors PV
Assembly Procedures
STRIPPING AND CRIMPING
3/16" for
#20 CONTACT
9/32" for
#16 CONTACT
9/32" for
#12 CONTACT
Right
Wrong
CONTACT INSERTION
OPENING
COLORED END
FOR INSERTION
CONTACT EXTRACTION
COMPLETION
BROKEN CIRCLE
BREAK
1. Strip wires according to contact size: 3/16" for #20 and 9/32"for
#16 and#12. #20 contacts accommodate AWG wire sizes 20, 22, or
24; #16 accommodates 16, 18 or 20; and #12 accommodates 12 or 14.
4. Insert contact and wire into tool jaws. To crimp, squeeze handles
together fully until ratchet release and allows handles to expand;
otherwise, contact cannot be extracted from tool jaws. Maintain slight
insertion pressure on wire while crimping contact to wire.
3. Slide back tool on wire shile holding thumb against wire at opening.
Wire will slip into tool.
NOTE: Socket contacts should be inserted partially into grommet
by hand before using insertion tool.
6. Withdraw tool from rear of plug. To be sure that contact is locked,
pull back lightly on wire. Then remove tool from wire and proceed with
other contacts.
2. Push tool into rear of plug until it bottoms. At this point, tool
releases tines on retaining clip so that contact can be extracted.
3. While maintaining slight insertion force on tool, firmly hold wire
against serrated shoulder at center of tool and extract both wired
contact and tool from plug.
4. Check face of plug or receptacle for proper contact installation. In
socket inserts with a large number of contact, cavities are identified in
a spiral pattern. A projecting line from the spiral indictates omission of a
letter; a broken circle around a cavity indicates transition between
capitals and lower case and double letters.
7. After all contacts are inserted, fill unwired cavities with sealing
plugs (insert head last and leave end protruding for ease of removal),
assemble backshell on rear of connector.
1. Remove backshell and slide back along wires to allow access. To
extract a contact, use white end of CIET tool. Place wire into tool at
large opening. Slide back tool on wire while holding thumb against wire
at opening. Wire will slip into tool.
4. With tool pressed against shoulder of contact, starting at the center
cavity, insert wired contact and tool into properly identified cavity at
rear of plug with firm, even pressure. Do not use excessive pressure.
5. When contact bottoms, a slight click can be heard as tines of metal
reataining clip snaps into place behind contact shoulder.
1. Remove backshell and put wired contacts thru cable clamp opening.
2. Used colored end of CIET tool for insertion. Place wire into tool at
large opening. To facilitate contact insertion, a 6-in. min. free lenght of
wire is recommended.
2. Insert wire into rear of contact. Wire insulation must butt against
rear of contact. Wire must be visible thru inspection hole.
3. Use M22520/1-01 crimp tool with proper crimp locator M22520/
1-02. The color code hand on the contact (red for #20, blue for #16
and yellow for #12) must match the color code of the locator and the
insertion tool throughout the crimping and assembly operations.
相關PDF資料 |
PDF描述 |
|---|---|
| MS3475L18-32AW | Series 2 Connectors PV |
| MS3475L18-32BW | Series 2 Connectors PV |
| MS3475L18-32PW | Series 2 Connectors PV |
| MS3475L18-32SW | Series 2 Connectors PV |
| MS3475L8-32AW | Series 2 Connectors PV |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MS3475L12-3A | 功能描述:CONN HSG PLUG CABLE 3 PIN RoHS:否 類別:連接器，互連式 >> 圓形 - 外殼 系列:軍用, MIL-C-26482 G 系列 II, AFD 標準包裝:1 系列:軍用, MIL-C-26482 G 系列 II, AFD 連接器類型:母觸點插座 位置數:41 外殼尺寸 - 插件:20-41 外殼尺寸，MIL:- 觸點類型：:壓接 觸點尺寸:20 安裝類型:面板安裝，法蘭 緊固型:插銷鎖 方向:Y 外殼材料，表面處理:鋁，鍍草綠色鎘 防護等級:抗環境影響 特點:- 包裝:散裝 請注意:不提供觸點 其它名稱:DMS3472W20-41SY-LC |
| MS3475L12-3AY | 功能描述:CONN HSG PLUG CABLE 3 PIN RoHS:否 類別:連接器，互連式 >> 圓形 - 外殼 系列:軍用, MIL-C-26482 G 系列 II, AFD 標準包裝:1 系列:軍用, MIL-C-26482 G 系列 II, AFD 連接器類型:母觸點插座 位置數:41 外殼尺寸 - 插件:20-41 外殼尺寸，MIL:- 觸點類型：:壓接 觸點尺寸:20 安裝類型:面板安裝，法蘭 緊固型:插銷鎖 方向:Y 外殼材料，表面處理:鋁，鍍草綠色鎘 防護等級:抗環境影響 特點:- 包裝:散裝 請注意:不提供觸點 其它名稱:DMS3472W20-41SY-LC |
| MS3475L12-3B | 功能描述:CONN HSG PLUG CABLE 3 SCKT RoHS:否 類別:連接器，互連式 >> 圓形 - 外殼 系列:軍用, MIL-C-26482 G 系列 II, AFD 標準包裝:1 系列:軍用, MIL-C-26482 G 系列 II, AFD 連接器類型:母觸點插座 位置數:10 外殼尺寸 - 插件:12-10 外殼尺寸，MIL:- 觸點類型：:壓接 觸點尺寸:20 安裝類型:自由懸掛 緊固型:插銷鎖 方向:Z 外殼材料，表面處理:鋁，鍍草綠色鎘 防護等級:抗環境影響 特點:- 包裝:散裝 請注意:不提供觸點 其它名稱:DMS3471W12-10BZ |
| MS3475L12-3BY | 功能描述:CONN HSG PLUG CABLE 3 SCKT RoHS:否 類別:連接器，互連式 >> 圓形 - 外殼 系列:軍用, MIL-C-26482 G 系列 II, AFD 標準包裝:1 系列:軍用, MIL-C-26482 G 系列 II, AFD 連接器類型:母觸點插座 位置數:10 外殼尺寸 - 插件:12-10 外殼尺寸，MIL:- 觸點類型：:壓接 觸點尺寸:20 安裝類型:自由懸掛 緊固型:插銷鎖 方向:Z 外殼材料，表面處理:鋁，鍍草綠色鎘 防護等級:抗環境影響 特點:- 包裝:散裝 請注意:不提供觸點 其它名稱:DMS3471W12-10BZ |
| MS3475L123P | 制造商:Amphenol Aerospace 功能描述:Conn MIL-C-26482 Circular PIN 3 POS Crimp ST Cable Mount 3 Terminal 1 Port 制造商:SOURIAU 功能描述:CONN PLUG 3POS STRAIGHT W/PINS |
發布緊急采購，3分鐘左右您將得到回復。