![](http://datasheet.mmic.net.cn/200000/MRFIC0912R2_datasheet_15084420/MRFIC0912R2_2.png)
MRFIC0912
2
MOTOROLA RF DEVICE DATA
MAXIMUM RATINGS (TA = 25°C unless otherwise noted)
Ratings
Symbol
Limit
Unit
Supply Voltage
VD1, VD2
8
Vdc
RF Input Power
PRF
20
dBm
Gate Voltage
VG1, VG2, VGG
–5
Vdc
Storage Temperature Range
Tstg
– 65 to +150
°C
Operating Case Temperature
TC
– 35 to +100
°C
Thermal Resistance, Junction to Case
R
θJC
18
°C/W
RECOMMENDED OPERATING RANGES
Parameter
Symbol
Value
Unit
RF Frequency
fRF
824–905
MHz
Supply Voltage
VD1, VD2
4.0–6.0
Vdc
Gate Voltage
VG1, VG2
–2.3 to –1.5
Vdc
ELECTRICAL CHARACTERISTICS (VD1, VD2 = 4.6 V, TA = 25°C, fRF = 840 MHz, Pin = 7 dBm, VGG set for ID2Q = 200 mA, Tested in
Circuit Shown in Figure 1)
Characteristic
Min
Typ
Max
Unit
RF Output Power
30.8
31.2
—
dBm
Power Slump (VD1, VD2 = 4.0 V, TC = 100_C)
28.5
—
dBm
Load Mismatch Survival (VD1, VD2 = 7 V, Load VSWR = 10:1, all phases,
10 sec)
No Degradation
Spurious Output (VD1,VD2 = 0 to 7 V, Pin = 5 to 9 dBm, Load
VSWR = 10:1)
—
–60
dBc
Input Return Loss
—
10
—
dB
Harmonic Output (Pout = 30.8 dBm)
2f0
3f0
4f0
—
–25
–40
dBc
Noise Power (VDD = 0 to 7 V, 45 MHz Above fRF at 30 kHz BW)
—
–93
dBm
Maximum Power Control Voltage Slope (Change in Pout for Change on
VD1)
—
45
—
dB/V
Total Supply Current (VD1 set for Pout = 30.8 dBm)
—
430
470
mA
VGG Required for ID2Q = 200 mA
–2.3
–2.0
–1.7
Vdc
Gate Current during RF Operation
–2
—
2
mA
DESIGN AND APPLICATIONS INFORMATION
The MRFIC0912 has been designed for high efficiency
900 MHz applications such as analog cellular and Industrial,
Medical and Scientific (ISM) equipment. The two stage MES-
FET design utilizes Motorola’s planar refractory gate process
to allow high performance GaAs to be applied to consumer
applications. The proprietary PFP–16 package assures good
grounding and low thermal resistance.
As shown in Figure 1, the gate voltage pins can be ganged
together and one voltage applied to both gates to set the
quiescent operating current. Alternatively, VG1 and VG2 can
be set separately. VD1 can be used as power control with a
45 dB per volt sensitivity. The placement of C3 in the VD1
supply line can be varied to optimize RF performance since
T2 is part of a shunt L matching section. On the output, pins
11, 12 and 13, the placement of C11 is adjusted for best RF
performance.
Layout is important for amplifier stability and RF perfor-
mance. Ground vias must be located as close to circuit
ground connections as possible. Power supply bypassing
C3, C6, C9, and C10 must be included to reduce out–of–
band gain and prevent spurious output.
Evaluation Boards
Evaluation boards are available for RF Monolithic Inte-
grated Circuits by adding a “TF” suffix to the device type.
For a complete list of currently available boards and ones
in development for newly introduced product, please con-
tact your local Motorola Distributor or Sales Office.