- 您現在的位置：買賣IC網 > PDF目錄299509 > MQHL-28E-15D-Z-C (SYNQOR INC) 2-OUTPUT 50 W DC-DC REG PWR SUPPLY MODULE PDF資料下載
參數資料
| 型號： | MQHL-28E-15D-Z-C |
| 廠商： | SYNQOR INC |
| 元件分類： | 電源模塊 |
| 英文描述： | 2-OUTPUT 50 W DC-DC REG PWR SUPPLY MODULE |
| 封裝： | MODULE-12 |
| 文件頁數： | 11/14頁 |
| 文件大?。?/td> | 4137K |
| 代理商： | MQHL-28E-15D-Z-C |
Product # MQHL-28E-15D
Phone 1-888-567-9596
www.synqor.com
Doc.# 005-0005929 Rev. 2
07/13/11
Page 6
Output:
Current:
±15V
3.3A Total
MQHL-28E-15D
Application Section
will restart. If the VIN input is brought down to nearly 0V
and back into the operating range, there is no startup inhibit,
and the output voltage will rise according to the “Turn-On
Delay, Rising Vin” specification.
SYNCHRONIZATION: The MQHL converter’s switching
frequency can be synchronized to an external frequency
source that is in the 500 kHz to 700 kHz range. A pulse
train at the desired frequency should be applied to the SYNC
IN pin (pin 6) with respect to the INPUT RETURN (pin 2).
This pulse train should have a duty cycle in the 20% to 80%
range. Its low value should be below 0.8V to be guaranteed
to be interpreted as a logic low, and its high value should
be above 2.0V to be guaranteed to be interpreted as a logic
high. The transition time between the two states should be
less than 300ns.
If the MQHL converter is not to be synchronized, the SYNC
IN pin should be left open circuit.
The converter will
then operate in its free-running mode at a frequency of
approximately 550 kHz.
If, due to a fault, the SYNC IN pin is held in either a logic low
or logic high state continuously, or the SYNC IN frequency
is outside the 500-700 kHz range, the MQHL converter will
revert to its free-running frequency.
The MQHL converter also has a SYNC OUT pin (pin 5). This
output can be used to drive the SYNC IN pins of as many as
ten (10) other MQHL converters. The pulse train coming out
of SYNC OUT has a duty cycle of 50% and a frequency that
matches the switching frequency of the converter with which
it is associated. This frequency is either the free-running
frequency if there is no valid synchronization signal at the
SYNC IN pin, or the synchronization frequency if there is.
The synchronization feature is entirely compatible with that
of SynQor’s MQFL family of converters.
Figure B shows the equivalent circuit looking into the SYNC
IN pin and Figure C shows the equivalent circuit looking into
the SYNC OUT pin.
OUTPUT VOLTAGE TRIM: If desired, it is possible to
increase or decrease the MQHL dual converter’s output
voltage from its nominal value. To increase the output voltage
a resistor, Rtrim up, should be connected between TRIM pin
(pin 10) and the OUTPUT RETURN pin (pin 8), as shown in
Figure D. The value of this resistor should be determined
according to the following equation of from Figure E:
PIN 2
PIN 6
5K
5V
SYNC IN
IN RTN
TO SYNC
CIRCUITRY
5K
Figure B: Equivalent circuit looking into the SYNC IN pin with
respect to the IN RTN (input return) pin.
FROM SYNC
CIRCUITRY
5K
5V
SYNC OUT
IN RTN
PIN 2
PIN 5
OPEN COLLECTOR
OUTPUT
Figure C: Equivalent circuit looking into SYNC OUT pin with
respect to the IN RTN (input return) pin.
where:
Vnom = the converter’s nominal output voltage,
Vout = the desired output voltage (greater than
Vnom), and
Rtrim up is in Ohms.
As the output voltage is trimmed up, it produces a greater
voltage stress on the converter’s internal components
and may cause the converter to fail to deliver the
desired output voltage at the low end of the input
voltage range at the higher end of the load current and
temperature range. Please consult the factory for details.
To trim the output voltage below its nominal value, connect
an external resistor (Rtrim down) between the TRIM pin
and the POSITIVE OUTPUT pin (pin 7), and another resistor
(Rtrim sense) connected between the TRIM pin and the
OUTPUT RETURN pin as shown in Figure D. The values of
these trim down resistors should be chosen according to the
following equation or from Figure E:
Rtrim up(Ω) = 8300Ω*Vnom
- 41700Ω
Vout - Vnom
Rtrim sense(Ω) = 0.43 * Rtrim down(Ω)
Rtrim down(Ω) = 50100Ω*Vout - 27500Ω*Vnom
- 137500Ω
Vnom - Vout
where:
Vnom = the converter’s nominal output voltage,
Vout = the desired output voltage (less than Vnom),
and
Rtrim down and Rtrim sense are in Ohms.
Factory trimmed converters are available by request.
advanced
publication
advanced
publication
advanced
publication
advanced
publication
相關PDF資料 |
PDF描述 |
|---|---|
| MR27V25603L-XXXTME | 16M X 16 MASK PROM, 120 ns, PDSO50 |
| MR4027P | UNIDIRECTIONAL, SILICON, TVS DIODE |
| MR7580-100P1BP | 100 CONTACT(S), MALE, D MICROMINIATURE CONNECTOR, SOLDER |
| MR7580-100P1BVU | 100 CONTACT(S), MALE, D MICROMINIATURE CONNECTOR, SOLDER |
| MR7580-100P2BR | 100 CONTACT(S), MALE, D MICROMINIATURE CONNECTOR, SOLDER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MQHL-28E-3R3S-W-ES | 制造商:SynQor 功能描述:MQHL-28E-3R3S-W-ES |
| MQIC3100H-17.000MHZ | 制造商:MMD MONITOR / QUARTZTEK 功能描述:bulk |
| MQK001-994-T7 | 功能描述:信號調節 VCO RoHS:否 制造商:EPCOS 產品:Duplexers 頻率:782 MHz, 751 MHz 頻率范圍: 電壓額定值: 帶寬: 阻抗:50 Ohms 端接類型:SMD/SMT 封裝 / 箱體:2.5 mm x 2 mm 工作溫度范圍:- 30 C to + 85 C 封裝:Reel |
| MQK002A1G06R6 | 功能描述:信號調節 VCO RoHS:否 制造商:EPCOS 產品:Duplexers 頻率:782 MHz, 751 MHz 頻率范圍: 電壓額定值: 帶寬: 阻抗:50 Ohms 端接類型:SMD/SMT 封裝 / 箱體:2.5 mm x 2 mm 工作溫度范圍:- 30 C to + 85 C 封裝:Reel |
| MQK300B1G71 | 功能描述:信號調節 VOLT CNTROL’D OSCILLATOR MS3 RoHS:否 制造商:EPCOS 產品:Duplexers 頻率:782 MHz, 751 MHz 頻率范圍: 電壓額定值: 帶寬: 阻抗:50 Ohms 端接類型:SMD/SMT 封裝 / 箱體:2.5 mm x 2 mm 工作溫度范圍:- 30 C to + 85 C 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。