- 您現在的位置：買賣IC網 > PDF目錄371127 > MMUN2114LT1 (ON SEMICONDUCTOR) PNP SILICON BIAS RESISTOR TRANSISTOR PDF資料下載
參數資料
| 型號： | MMUN2114LT1 |
| 廠商： | ON SEMICONDUCTOR |
| 元件分類： | 小信號晶體管 |
| 英文描述： | PNP SILICON BIAS RESISTOR TRANSISTOR |
| 中文描述： | 100 mA, 50 V, PNP, Si, SMALL SIGNAL TRANSISTOR, TO-236AB |
| 封裝： | CASE 318-08, TO-236, 3 PIN |
| 文件頁數： | 9/10頁 |
| 文件大?。?/td> | 267K |
| 代理商： | MMUN2114LT1 |
9
Motorola Small–Signal Transistors, FETs and Diodes Device Data
SOLDER STENCIL GUIDELINES
Prior to placing surface mount components onto a printed
circuit board, solder paste must be applied to the pads. A
solder stencil is required to screen the optimum amount of
solder paste onto the footprint. The stencil is made of brass
or stainless steel with a typical thickness of 0.008 inches
The stencil opening size for the surface mounted package
should be the same as the pad size on the printed circuit
board, i.e., a 1:1 registration.
TYPICAL SOLDER HEATING PROFILE
For any given circuit board, there will be a group of control
settings that will give the desired heat pattern. The operator
must set temperatures for several heating zones, and a
figure for belt speed. Taken together, these control settings
make up a heating “profile” for that particular circuit board.
On machines controlled by a computer, the computer
remembers these profiles from one operating session to the
next. Figure 23 shows a typical heating profile for use when
soldering a surface mount device to a printed circuit board.
This profile will vary among soldering systems but it is a good
starting point. Factors that can affect the profile include the
type of soldering system in use, density and types of
components on the board, type of solder used, and the type
of board or substrate material being used. This profile shows
temperature versus time. The line on the graph shows the
actual temperature that might be experienced on the surface
of a test board at or near a central solder joint. The two
profiles are based on a high density and a low density board.
The Vitronics SMD310 convection/infrared reflow soldering
system was used to generate this profile. The type of solder
used was 62/36/2 Tin Lead Silver with a melting point
between 177–189
°
C. When this type of furnace is used for
solder reflow work, the circuit boards and solder joints tend to
heat first. The components on the board are then heated by
conduction. The circuit board, because it has a large surface
area, absorbs the thermal energy more efficiently, then
distributes this energy to the components. Because of this
effect, the main body of a component may be up to 30
degrees cooler than the adjacent solder joints.
STEP 1
PREHEAT
ZONE 1
“RAMP”
DESIRED CURVE FOR HIGH
MASS ASSEMBLIES
STEP 2
VENT
“SOAK”
STEP 3
HEATING
ZONES 2 & 5
“RAMP”
STEP 4
HEATING
ZONES 3 & 6
“SOAK”
STEP 5
HEATING
ZONES 4 & 7
“SPIKE”
170
°
C
STEP 6
VENT
STEP 7
COOLING
200
°
C
150
°
C
100
°
C
50
°
C
TIME (3 TO 7 MINUTES TOTAL)
TMAX
SOLDER IS LIQUID FOR
40 TO 80 SECONDS
(DEPENDING ON
MASS OF ASSEMBLY)
205
°
TO
219
°
C
PEAK AT
SOLDER
JOINT
DESIRED CURVE FOR LOW
MASS ASSEMBLIES
100
°
C
150
°
C
160
°
C
140
°
C
Figure 23. Typical Solder Heating Profile
相關PDF資料 |
PDF描述 |
|---|---|
| MMUN2115LT1 | PNP SILICON BIAS RESISTOR TRANSISTOR |
| MMUN2130LT1 | PNP SILICON BIAS RESISTOR TRANSISTOR |
| MMUN2116LT1 | PNP SILICON BIAS RESISTOR TRANSISTOR |
| MMUN2131LT1 | PNP SILICON BIAS RESISTOR TRANSISTOR |
| MMUN2132LT1 | PNP SILICON BIAS RESISTOR TRANSISTOR |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MMUN2114LT1 WAF | 制造商:ON Semiconductor 功能描述: |
| MMUN2114LT1G | 功能描述:開關晶體管 - 偏壓電阻器 100mA 50V BRT PNP RoHS:否 制造商:ON Semiconductor 配置: 晶體管極性:NPN/PNP 典型輸入電阻器: 典型電阻器比率: 安裝風格:SMD/SMT 封裝 / 箱體: 直流集電極/Base Gain hfe Min:200 mA 最大工作頻率: 集電極—發射極最大電壓 VCEO:50 V 集電極連續電流:150 mA 峰值直流集電極電流: 功率耗散:200 mW 最大工作溫度: 封裝:Reel |
| MMUN2114LT3 | 制造商:LRC 制造商全稱:Leshan Radio Company 功能描述:Bias Resistor Transistors |
| MMUN2114LT3G | 功能描述:肖特基二極管與整流器 SS BR XSTR PNP 50V SOT23 RoHS:否 制造商:Skyworks Solutions, Inc. 產品:Schottky Diodes 峰值反向電壓:2 V 正向連續電流:50 mA 最大浪涌電流: 配置:Crossover Quad 恢復時間: 正向電壓下降:370 mV 最大反向漏泄電流: 最大功率耗散:75 mW 工作溫度范圍:- 65 C to + 150 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-143 封裝:Reel |
| MMUN2114RLT1 | 制造商:LRC 制造商全稱:Leshan Radio Company 功能描述:Bias Resistor Transistor |
發布緊急采購，3分鐘左右您將得到回復。