參數資料
型號： MM908E625
廠商： 飛思卡爾半導體(中國)有限公司
英文描述： Integrated Quad Half H-Bridge with Power Supply, Embedded MCU, and LIN Serial Communication(集成四半H橋，帶電源、嵌入式MCU和LIN串行通信功能)
中文描述： 綜合四半僅符合電源橋，嵌入式微控制器和LIN串行通信（集成四半魔橋，帶電源，嵌入式微控制器和林串行通信功能）
文件頁數： 27/40頁
文件大?。?/td> 595K
代理商： MM908E625
MOTOROLA ANALOG INTEGRATED CIRCUIT DEVICE DATA
908E625
27
Figure 13. Hall-Effect Sensor Input Terminal Connected to Three-Terminal Hall-Effect Sensor
Interrupts
The Hall-effect sensor input terminals are interrupt capable.
How and when an interrupt occurs is dependent on the
operating mode, RUN or Stop.
RUN Mode
In RUN mode the Hall-effect sensor input terminal interrupt
flag (HPF) will be set if a state change on the hallflags (HxF) is
detected. The interrupt is maskable with the HPIE bit in the
Interrupt Mask Register. Before enabling the interrupt, the flag
should be cleared in order to prevent a wrong interrupt.
STOP Mode
In STOP mode the Hall-effect sensor input terminals are
disabled independent of the state of the HxEN flags.
Cyclic Wake-Up
The Hall-effect sensor inputs can be used to wake up the
system. This wake-up function is provided by the cyclic check
wake-up feature of the AWD (autonomous watchdog).
If the cyclic check wake-up feature is enabled (AWDCC bit is
set), the AWD switches on the enabled Hall-effect sensor
terminals periodically. To ensure that the Hall-effect sensor
current is stabilized after switching on, the inputs are sensed
after ~40
μ
s. If a “1” is detected (I
Hall sensor
> I
HSCT
) and the
interrupt mask bit HPIE is set, an interrupt is performed.
This
wakes up the MCU and starts the main voltage regulator.
The wake-up function via this input is available when all three
conditions exist:
The two-terminal Hall-effect sensor input is enabled
(HxEN = 1).
The cyclic wake-up of the AWD is enabled (AWDCC = 1)
(see
Figure 14
, page 28).
The Hall-effect sensor input terminal interrupt is enabled
(HPIE = 1).
HxEN
HxF
Sense
Circuitry
V
Hx
GND
Three-Terminal Hall-Effect Sensor
Out
Vs
GND
F
Freescale Semiconductor, Inc.
For More Information On This Product,
Go to: www.freescale.com
n
.
相關PDF資料
PDF描述
MM908E626AVDWB Integrated Stepper Motor Driver with Embedded MCU and LIN Serial Communication
MM908E626R2 Integrated Stepper Motor Driver with Embedded MCU and LIN Serial Communication
MM908E626 Integrated Stepper Motor Driver with Embedded MCU and LIN Serial Communication
MMA1200D Surface Mount Micromachined Accelerometer(表面安裝微電機加速計)
MMA1200 Surface Mount Micromachined Accelerometer
相關代理商/技術參數
參數描述
MM908E625ACDWB 功能描述:8位微控制器 -MCU 32 Bit 8MHz RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
MM908E625ACDWB/R2 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:Integrated Quad Half H-Bridge with Power Supply, Embedded MCU, and LIN Serial Communication
MM908E625ACEK 功能描述:8位微控制器 -MCU Quad Half H-Bridge with P/S, HC08, LIN RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
MM908E625ACPEK 功能描述:8位微控制器 -MCU R0 HI-BRDG EMBED MCU LIN RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
MM908E626 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Integrated Stepper Motor Driver with Embedded MCU and LIN Serial Communication
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*